Bedienungsanleitung Adler AD 7852 (Seite 5 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

800042

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

electrician for this.

14. Clean the air filter regularly. The frequency of cleaning depends on the cleanliness of

the air.

15. After turning off the machine, wait at least 5 minutes before turning it back on.

16. Do not use the device in sunny places. When the device overheats, the overheat

protection will switch on the device.

17. To ensure effective cooling, a distance of at least 60 cm should be kept between the

side walls of the device and the wall or furniture or curtains.

18. Due to the limited performance of the device, if the difference between the target

temperature and the ambient temperature is too great, the target temperature may not

be reached.

19. To reduce the risk of fire, electric shock or injury when using the air conditioner,

observe the following basic precautions:

a) Connect to a grounded outlet with 3 pins.

b) Do not remove the grounding prong.

c) Do not use the adapter.

d) Do not use an extension cord.

e) Disconnect the air conditioner before servicing.

f) Use two or more people to move and install the air conditioner.

20. Do not use agents accelerating the defrosting or cleaning process other than those

recommended by the manufacturer.

21. The device should be stored in a room without constantly operating sources of

ignition, for example: open fire, gas appliances or electric heaters.

BEFORE FIRST USE – (picture E)

Connect the connectors to the air exhaust duct as follows:

1. Extend the air exhaust duct (10) by drawing out the two ends of the duct.

2. Screw the air exhaust duct (10) into the connector of air exhaust duct (11).

3. Connect the connector of air exhaust duct (11) to the device.

REMARKS:

1.Keep the unit at least 1 meter away from TV or radios to avoid electromagnetic interference.

2.Do not expose the unit under direct sun light to avoid surface color fading.

3.Do not tilt the unit for more than 35°or upside-down while transporting. If the device has been turned over during transport, put it

down correctly and wait 2-4 hours before starting it.

4.Place the unit on a flat surface with less than 5°inclination.

5.The unit operates more efficiently in certain room locations, select the best location:

- Beside a window, a door or a French window.

- Keep the required distance from the return air outlet to the wall or other obstacles at least 60 cm.

- Extend the air hose to ensure that other end of the air hose has clearance between the window door, or French window, or wall

hole.

- Air outlet or intake cannot be blocked by protective grid or any obstacle.

To extend the life of the unit, drain the condensed water from the upper (8) and lower (9) cooler drain holes before putting the unit

into storage at the end of the season.

DEVICE DESCRIPTION (pictures A and B)

1. Control panel 2. Cold air outlet

3. Signal receptor 4. Remote controller

5. Transport handle 6. Exhaust duct

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adler AD 7852 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info