Bedienungsanleitung Adler AD 7921 (Seite 6 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

800050

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste

bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may

effect the environment. Do not dispose this appliance in the common waste bin.

3. Turn on the device using the power switch (A) button on the control panel (Fig. C). default setting is middle fan speed. Press power

switch (A) again, product is in standby.

4. The fan speed button (E) on the control panel (9) allows you to change the speed of the fan. The following fan speeds can be selected

by pressing again: medium (H) -> slow (G) -> fast (H) -> medium (H) -> …

5. Cooling / Humidify button (B) lowers the temperature of the air by running the water pump. Additionally, you can put to upper water

tank (2) attached plastic containers (3). Plastic containers (3) should be filled up to max level by water and frozen in the freezer in

advance.

To blow the cool air, the device must be filled with water. When the device is operating, periodically check the water level to see whether

to add water. NEVER switch on the water pump when the bottom water tank (6) is not filled by water to minimum level at least.

a)Unplug the device, remove the screw of the back housing and then take mesh filter (11) and evaporation paper filter (13) out.

b)Wash the evaporation paper filter (13) in a mild detergent and warm water solution by soft brush, then rinse in clean water. Take care

not to pierce the evaporation paper filter (13).

-on fan speed set to low speed (G): the fan will blow 5 seconds at low speed and turn off for 5 seconds and next repeat this cycle;

-on fan speed set to fast speed (I): the fan will blow 30 minutes on fast speed natural mode then switch to middle speed natural mode

for 30 minutes, then switch to low speed natural mode.

-on fan speed set to low speed (G): the fan will run the same as low speed natural mode;

8. The mode choice button (C) allows for changing the fan mode. In addition to the normal fan air wind mode, you can select natural and

sleep modes.

-on fan speed set to middle speed (H): the fan will blow 5 seconds on each speed: middle , low, middle, stop, low, middle, low, stop and

next repeat this cycle;

c)Wash the mesh filer (11) with flowing clean water. Use a soft brush for cleaning.

1. Clean with soft, dry cloth. Do not use chemical solvents because they can cause permanent damage or deformation of the device.

3. After long time operation, mesh filter (11) and evaporation paper filter (13) will be clogged with the dust, which will greatly affect the

machine’s performance of cooling. If long time no changing water, there may be mold and mildew. We suggest to clean the mesh filter

(11) and evaporation paper filter (13) once every two weeks. The clean procedure is as below:

d) Dry both filters. The evaporation paper filter (13) must be installed flatly in order to avoid leakage. Screw bracket (15) with evaporation

paper filter (13) and mesh filter (11) to housing.

4. Drain the water before storage by removing the drain plug (12) at the bottom of the water tank after each use.

7. The TIMER button (F) allows for programming the amount of time during which the device will operate before turning itself off

automatically. Available time period selection is: 2-4-6-8-10-12 hours.

Normal fan mode (J) allows to set up fan speed between: medium (H) -> slow (G) -> fast (H) -> medium (H) -> … Each time the fan is

turned on again it will start operation in normal mode.

The natural mode (K) mimics the natural wind action by repeating the fan speed sequence:

-on fan speed set to fast speed (I): the fan will blow 5 seconds each speed: middle, low, fast, middle, fast, low, fast, stop and next repeat

this cycle.

-on fan speed set to middle speed (H): the fan will blow 30 minutes on middle speed natural mode, then switch to low speed natural

mode;

To start remote control (14) operation pull out the installing film. To replace the battery push the release tab and take battery out the

battery carriage. Replace by same type battery.

Sleep mode (L) was designed to use the effects of nature wind to easier fall asleep. It will gradually decrease the speed of fan in 30

minute increments:

CLEANING AND MAINTENANCE

Please ensure that the device and all of its parts are cleaned regularly to reduce the risk of limescale and bacteria forming. Unplug the

device before cleaning. Do not soak the control panel in water.

6. Pressing the horizontal air osculation button (D) to start the oscillation of slats that provide even distribution of cold air stream in range

70°. Horizontal louvers (4) do not move automatically, so if necessary, manually adjust them to point up or down.

2. If the device is not used for three or more months, take the batteries out of the remote control.

Tank capacity: 5,5 liters

Power source: 220-240 V ~50 Hz

6. Assemble the device and store it in a dry place until the next season.

Power: 60W

Water Consumption: 300ml / hour

Power Max: 300W

5. Before season storage clean bottom water tank (6) after unscrewing 3 screws. Then dry water tank, filters and housing to avoid the

moisture damage.

TECHNICAL DATA:

Remote control supplied by lithium type battery CR2025 (3V), included

Adler AD 7921 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info