Bedienungsanleitung Adler AD 7968 (Seite 5 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

800056

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

- First press: continuous mist with alternating 7 RGB LED colors.

- Second press (double flash): intermittent mist generation (15 second pauses) with alternating 7 RGB LED colors.

- Third press: Turns off the device (mist generation and lighting stop simultaneously).

Backlight button (O):

- First press: 7 RGB LED colors alternating.

- Second press: constantly backlight with the last glowing color.

- Third press: imitating the natural light of a burning candle mode.

- Fourth press: Turn off the backlight.

7. If there is no water in the water tank (C), the diffuser will be turned off automatically.

8. The product cannot be used if there is no water in the tank (C).

NOTE: The mist concentration may vary slightly, which is normal. Different types of water, humidity, temperature and air velocity affect

spray intensity.

9. Before replacing with another oil, please clean the device according to the maintenance instructions.

10. Never leave water in the tank (C) and disconnect the USB cable (K) when the device is not in use.

11. After working for a long time, turn off the device for 60 minutes to avoid damaging the ultrasonic wave atomizer, and then turn it on

again.

ACCIDENTAL LEAK

If you accidentally tip your device over while in use, follow these steps:

1. Turn off the power. Unplug the appliance and open the lid (B) to pour out all the remaining water from the water tank (C).

2. Gently shake the device to drain the internal water.

3. Air dry the device in a safe place for 24 hours.

DESCALING

If there is limescale deposited in the aroma diffuser caused by water, you can add white vinegar to the water to dissolve the limescale,

leave it for 20 minutes, then rinse with water. Then use a soft cloth to wipe off the water. Never use strong cleaning agents.

TROUBLESHOOTING

If this product is not working normally, please follow these steps for self- troubleshooting before sending the return to the seller:

PROBLEM 1: The product automatically turns off in one second when the N spray button is turned on.

POSSIBLE CAUSE: Inadequate amount of water.

SOLUTION: Please add water to the water tank or drain if it exceeds the MAX level.

POSSIBLE CAUSE: The USB cable is not connected to the device.

SOLUTION: Make sure the USB cable is connected to the product and to the power source properly.

PROBLEM 2: No spray or abnormal spray

POSSIBLE CAUSE: Inadequate amount of water.

SOLUTION: Please add water to the water tank if there is not enough. If the water level inside the water tank is higher than the

maximum water level mark, the mist will be sprayed irregularly, abnormally. Drain the water so that it is below the "MAX" level.

POSSIBLE CAUSE: The atomizer ceramic plate (I) is dirty.

SOLUTION: Please clean the water tank (C) and the ceramic atomizer plate (I).

POSSIBLE CAUSE: Lower air inlet holes (G) are dusty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adler AD 7968 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info