Bedienungsanleitung Adler AD 7969 (Seite 6 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

800057

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

- Third press: Power off the device. (FIG.6)

7. If there is no water in the water tank (C), the diffuser will be turned off automatically.

8. The product cannot be used if there is no water in the tank (C).

NOTE: The mist concentration may vary slightly, which is normal. Different types of water, humidity, temperature and air velocity affect

spray intensity.

9. Before replacing with another oil, please clean the device according to the maintenance instructions.

10. Never leave water in the tank (C) when the device is not in use.

10. After working for a long time, turn off the device for 60 minutes to avoid damaging the ultrasonic wave chip, and then restart it.

ACCIDENTAL LEAK

If you accidentally tip your device over while in use, follow these steps:

1. Turn off the power. Unplug the appliance and open the lid (B) to pour out all the remaining water from the water tank (C).

2. Gently shake the device to drain the internal water.

3. Air dry the device in a safe place for 24 hours.

DESCALING

If there is limescale build up in the aroma diffuser caused by water, you can add white vinegar to the water to dissolve the limescale,

then rinse with water. Then use a soft cloth to wipe off the water. Never use strong cleaning agents.

TROUBLESHOOTING

If this product is not working normally, please follow these steps for self- troubleshooting before sending the return to the seller:

PROBLEM 1: The product automatically turns off one second after being turned on.

POSSIBLE CAUSE: Inadequate amount of water.

SOLUTION: Please add water to the water tank.

POSSIBLE CAUSE: The power adapter is not connected to the device.

SOLUTION: Make sure the power adapter is connected to the product. To check if the connection was successful, please remove the

cable from the micro-USB socket and reconnect it

PROBLEM 2: No spray or abnormal spray

POSSIBLE CAUSE: Inadequate amount of water.

SOLUTION: Please add water to the water tank if there is not enough. If the water level inside the water tank is higher than the

maximum water level mark, the mist will be sprayed irregularly, abnormally. Drain the water so that it is below the "MAX" level.

POSSIBLE CAUSE: Ultrasonic spray chip (I) is dirty.

SOLUTION: Please clean the water tank (C) and chip (I). Oils sometimes accumulate on the ultrasonic spray chip board.

POSSIBLE CAUSE: Lower air inlet holes (H) are dusty.

SOLUTION: If the air inlet holes (G) are dusty, the volume of air drawn in will be reduced significantly and the air momentum will not be

enough to spray the mist. Clean the air intake.

PROBLEM 3: Leakage

POSSIBLE CAUSE: Lid (B) is not closed properly.

SOLUTION: Close the lid securely.

POSSIBLE CAUSE: Room temperature is too low or humidity is too high.

SOLUTION: If the temperature or humidity of the working environment is too low or too high, mist and water drops will accumulate on the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adler AD 7969 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info