Bedienungsanleitung Adler AD 8085 (Seite 4 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

800069

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

2A. Mode switch - heating (HOT) / switching off (OFF) / cooling (COLD)

DEVICE DESCRIPTION:

2C. Car power socket 12V

current not exceeding 30 mA. A specialist electrician should be consulted in this regard.

15. Only original assembly parts and power cables supplied by the manufacturer in the set

with the device should be used.

16.Do not overload the refrigerator. The cover must close freely.

1D. Power supply cable for the home electrical installation

2D. 220-240V~ power socket

3A. Mini fridge chamber with aluminum cavity 3B. Shelf 3C. Mini basket 3D. Handle 3E. Mirror

USING THE APPLIANCE

23. Only ready-made (wrapped) articles may be stored in the refrigerator.

24. Prevent the appliance from being upside down. Don't drop or shock it.

22. Never connect the power cord to both the cigarette lighter and the electricity supply to

the refrigerator at the same time.

25. Store food in original packaging or containers intended for this purpose.

1A. Control panel 1B. Fan 1C. Car power cable

17. WARNING: Be careful that the products stored inside do not cover the vent.

18. Use the refrigerator in an upright position only.

19. Do not expose the refrigerator to direct sunlight, rain, snow, excessive moisture, etc..

20. Exercise particular caution when transporting the switched-on device in a car. Protect

against falling while driving.

21. WARNING: Keep space around the ventilation openings. Covering them will reduce the

cooling capacity and may damage the refrigerator.

2B. Voltage switch – DC (12V ) / switching off (OFF) / AC (220-240V~)

DC: Heating mode 32W / Cooling mode 36W

b) Set the voltage switch (2B) to DC.

a) Insert the other end of the cable with the plug (1C) into the cigarette lighter socket.

c) Plug in the connector to the DC slot (2C).

c) Insert the other end of the cable with the plug (1D) into the electric socket.

WARNING: Don't switch the mode switch (2A) abruptly. Switch the function after 30 minutes of being on position: OFF.

2. The cleaning process is restricted to using a damp cloth with a little of washing up liquid on the inside and outside of the devices body.

NOTE: DO NOT PUT ANY FOREIGN OBJECTS INTO THE FAN TO CLEAN IT.

d) Set the mode switch (2A) to: “HOT" when you want to heat the chamber or "COLD" to cool the chamber.

2. Device operation:

With AC220-240V power supply:

a) Plug in the connector to the AC slot (2D).

The power consumption on each setting is as below:

AC: Heating mode 38W / Cooling mode 42W

3. After finishing operation, set the mode switch (2A) and voltage switch (2B) to "OFF" and disconnect the wires.

1. Ensure that the power switch (2A) on the control panel (1A) of the refrigerator is in the OFF position.

Cleaning and Maintenance

d) Set the mode switch (2A) to: “HOT" when you want to heat the chamber or "COLD" to cool the chamber.

The power consumption on each setting is as below:

1. Before cleaning make sure that the device is not connected to the power source.

With 12V DC power supply:

b) Set the voltage switch (2B) to AC.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adler AD 8085 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info