Bedienungsanleitung Adobe ILLUSTRATOR (Seite 39 von 545) (Englisch)

548118

Zoom out

Zoom in

Vorherige Seite

1/545

Nächste Seite

To the top

2. Choose Object > Path > Simplify.

3. Set the Curve Precision to control how closely the simplified path follows the original path.

Select Preview to show a preview of the simplified path and list the number of points in the original and simplified paths.

4. Select additional options, and click OK:

Curve Precision Enter a value between 0% and 100% to set how closely the simplified path should follow the original path. A higher

percentage creates more points and a closer fit. Any existing anchor points are ignored except for endpoints of a curve and corner points

(unless you enter a value for Angle Threshold).

Angle Threshold Enter a value between 0 and 180° to control the smoothness of corners. If the angle of a corner point is less than the

angle threshold, the corner point is not changed. This option helps keep corners sharp, even if the value for Curve Precision is low.

Straight Lines Creates straight lines between the object’s original anchor points. Corner points are removed if they have an angle greater

than the value set in Angle Threshold.

Show Original Shows the original path behind the simplified path.

Average the position of anchor points

1. Select two or more anchor points (on the same path or on different paths).

2. Choose Object > Path > Average.

3. Choose to average along the horizontal (x) axis only, the vertical (y) axis only, or both axes, and click OK.

Convert between smooth points and corner points

You can convert the points on a path between corner to smooth points. Using options in the Control panel, you can quickly convert multiple anchor

points. Using the Convert Anchor Point tool, you can choose to convert only one side of the point, and you can precisely alter the curve as you

convert the point.

Convert one or more anchor points using the Control panel

To use the anchor point conversion options in the Control panel, only relevant anchor points, not the entire object, should be selected. If you select

multiple objects, one of the objects must be only partially selected. When entire objects are selected, the Control panel options change to those

that affect the entire object.

1. To convert one or more corner points to smooth points, select the points and then click the Convert Selected Anchor Points To Smooth

button in the Control panel.

2. To convert one or more smooth points to corner points, select the points and then click the Convert Selected Anchor Points To Corner

button in the Control panel.

Convert an anchor point precisely using the Convert Anchor Point tool

1. Select the entire path you want to modify so that you can see its anchor points.

2. Select the Convert Anchor Point tool .

3. Position the Convert Anchor Point tool over the anchor point you want to convert, and do one of the following:

To convert a corner point to a smooth point, drag a direction point out of the corner point.

Dragging a direction point out of a corner point to create a smooth point

To convert a smooth point to a corner point without direction lines, click the smooth point.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Adobe ILLUSTRATOR Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Adobe ILLUSTRATOR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info