Bedienungsanleitung Aduro 11 eco (Seite 19 von 38) (Deutsch, Englisch, Dänisch, Französisch, Schwedisch)

711961

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

_______________________________________________________________________________________________________________________________

- 19 -

0 Installation of the wood burning stove

You are welcome to install your wood burning stove yourself – but we strongly recommend that you consult your

chimney sweep before you begin the installation. Your dealer can also provide you with installation advice. It is

important to ensure that all local rules and regulations, including ones relating to national and European standards,

are complied with when installing this device.

Please note: You may not begin to use the wood burning stove until it has been inspected and approved by your

local chimney sweep.

2.1 Position of the stove/distance requirements

The new wood burning stove must be installed in a suitable and physically possible position. You need to be sure

that the position complies with local regulations. Distance requirements will only apply if the wood burning stove is to

be placed close to flammable materials. The Aduro 11 should be installed at a distance of 20 cm from flammable

materials at the rear and at a distance of 30 cm from the side. All furniture must be kept at least 85 cm away from

the front of the stove. If the stove is installed with an insulated pipe then you may reduce the distance behind the

stove to 10 cm. See illustration below. The distances are measured from the top of the stove.

If the stove is positioned against a brick wall or other non-flammable material, there is no minimum distance

requirement. To facilitate cleaning and for the best use of the convection air, we recommend that you leave a

distance of approximately 5–10 cm to the wall. The Aduro 11 is built as a convection stove. This means that air from

the room circulates between the inner stove and the outer covering. As a result, the heated air is distributed evenly

throughout the room.

Behind stove

3030

20/10*

* When using an insulated pipe

Please note: that the Aduro 11 must be installed on a floor with the adequate load-bearing capacity. If the existing

construction does not meet this requirement, appropriate adaptation measures must be taken (e.g. a load-

distributing plate).

If the wood burning stove is to be placed close to flammable material, such as a wooden floor or carpet, it must be

placed on a non-flammable base. The floor plate should extend for at least 30 cm in front of the wood burning

stove, and 15 cm on each side.

2.2 Pipe connection

Aduro 11 leaves the factory with the flue outlet mounted on the top. If you require the flue outlet on the back,

remove the round circle from the rear cover at the upper rear of the stove. The cover plate (that covers the rear

outlet) should then be moved to the top outlet. The top outlet is finished with the plate that lies in the ash drawer. A

flue pipe with an internal diameter of 150 mm should be used for Aduro stoves.

Dansk | Deutsch | English | Francais | Svenska

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aduro 11 eco Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info