Bedienungsanleitung Aduro 15-3 (Seite 26 von 44) (Deutsch, Englisch, Dänisch, Französisch, Schwedisch)

632344

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

_______________________________________________________________________________________________________________________________

4.0 The chimney

Data for chimney calculation:

Wood

Flue temperature at [20 C]

395

Chimney draught at testing power

[mbar]/[Pa]

0,12/12

Flue gas mass flow [g/s]

5,4

The optimum combustion is achieved at a constant chimney draught of 0.10 to 0.14 mbar measured in the flue pipe

above the stove. There are many factors that affect the chimney draught, including the outside temperature, wind

strength and surrounding buildings. If it is impossible to establish a sufficiently natural chimney draught, the

chimney can be fitted with a smoke extractor. If the chimney draught is too strong, a damper can be fitted to

regulate the chimney draught. Contact your local chimney sweep for more advice.

There are no requirements with respect to specific chimney heights, but a chimney must be tall enough to provide a

good draught – above 12 Pa. If the recommended chimney draught is not achieved, there may be problems with

smoke out of the door by firing.

4.1 Inadequate draught in the chimney

If the chimney is too short, leaks or is inadequately insulated, there may be problems with the chimney draught (let

the chimney sweep assess this). The draught should be approx. 0.10–0.14 mbar in order to provide satisfactory

combustion and prevent smoke leakage.

If the chimney sweep judges the draught to be satisfactory, but you still have problems lighting a fire, try extending

the fire lighting phase/using more thin pieces of kindling, so that the chimney gets thoroughly warm. The chimney

will not draw at optimum effect until it is warm. The fire lighting phase can be prolonged by using a lot of kindling

and 1-2 firelighters. When a layer of embers has been formed, add 2–3 dry logs.

5.0 Maintaining and cleaning your wood burning stove

Gaskets

With time, the gaskets will wear, and, in order to avoid wild combustion, they must be replaced as required.

Glass

If the wood you burn is too moist, you will get soot stains on the glass pane. They can be easily removed using a

damp cloth that you dip in cold ash and rub on the sooty glass. Special cleaning agents are also available to

remove soot from glass, i.e. the Aduro Easy Clean pad.

Combustion chamber

The yellow tiles in the combustion chamber eventually wear out and they should be replaced when the cracks are

more that 0.5 cm. The durability of the tiles will depend on how often and how intensively the stove is used. You

can change the tiles yourself. They are available as a ready-to-use set. You can also buy one-piece tiles that you

can cut to the size of the worn plates yourself. Please visit www.aduroshop.com.

Ash

Empty the ash drawer before it becomes completely full. Always leave a layer of ash on the bottom of the stove, as

this insulates the combustion chamber and makes lighting a fire easier.

Cleaning the wood burning stove

The stove’s surface is treated with a heat-resistant Senotherm® paint, which will stay at its best just by being

vacuumed with a small, soft mouthpiece or dusted with a soft, dry cloth. Do not use water, spirit or other solvents

which will remove the paint.

The inside of the wood burning stove and the flue pipe can be cleaned via the door and the cleaning aperture in the

flue pipe/chimney. The upper fireproof tile (the exhaust deflector) can be removed. To allow free access to the top

of the wood burning stove and the flue pipe, remove the exhaust deflector in steel. Cleaning of the inside of the

wood burning stove and the flue pipe should be undertaken at least once a year, or more frequently if necessary,

depending on how often the wood burning stove is used. This work can also be carried out by the chimney sweep.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aduro 15-3 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Aduro 15-3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info