Bedienungsanleitung Aduro 9-4 (Seite 27 von 47) (Deutsch, Englisch, Dänisch, Französisch, Schwedisch)

632353

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

_______________________________________________________________________________________________________________________________

The first few times the wood burning stove is used, there may be some smoke and unpleasant odours from the

wood burning stove, which is fairly normal. This is caused by the heat-resistant paint hardening. Make sure there is

sufficient ventilation during this stage. It is also important not to let the fire burn too fiercely the first 2–3 times, so

that the wood burning stove has time to expand slowly. You should also be aware that the stove may make clicking

sounds as it heats up and cools down – rather like pouring boiling water into a sink. These are caused by the great

differences in temperature to which the materials are being exposed.

During the first firing, which should be carried out using approximately 1 kg of wood, the stoking door must be left

slightly open and must not be closed until the stove is cold. This is to prevent the sealing rope sticking to the stove.

3.5 How should I use my wood burning stove?

The wood burning stove is intended for intermittent combustion. This means that each stoking should burn down to

embers before new logs are added.

In order to obtain the best possible combustion, you should regulate the effect/heat output with the fuel. Burning

small logs provides more powerful combustion than burning large logs as the surface area is greater and more gas

is released. The amount of wood in the combustion chamber is another factor that affects combustion. In normal

circumstances, you should not place more than two logs in the stove. If you want an enhanced effect, you can add

more logs. The nominal heat output is reached by burning approx. 2.2 kg per hour.

3.6 Secondary damper

The secondary damper behind the door should always be open while the wood burning stove is in use. This

damper allows you to adjust the wood burning stove to the chimney draft and the heat output you require. In normal

circumstances, the wood burning stove should be working with this damper open between 60 % and 100 %. You

should never close the air intake so far that the flames are extinguished. There should always be visible flames in

order to achieve clean and efficient combustion. A too low supply of air can lead to bad combustion, high emissions

and a bad efficiency. The air-wash system, that minimizes soot collecting on the front glass pane, is also adjusted

by this damper.

3.6.1 Secondary damper side glass

The secondary damper over the side glass allows you to adjust the wood burning stove to

the chimney draft and the heat output you require. It also helps to keep the side glass

clean when opened.

Aduro Key: provides easier control of the secondary damper. The key is fitted onto the

control handle, so you can more easily adjust the airflow from side to side. Turning to the

left decreases the airflow, and turning to the right increases the airflow.

3.7 Primary damper

When you add a new log, the primary air intake/damper should be opened until the fire is burning properly. In order

to utilize the fuel to the fullest extent, the embers should have burnt for so long that it is necessary to open the

primary air intake for approx. 2 minutes to get the new log to burn.

In order to reduce the risk of ash falling from the stove when the door is opened to add more fuel, it is a good idea

to open the primary air intake/damper for approx. 1 minute before the door is opened. This increases the draught

through the stove and reduces the risk that ash will drop on the floor.

Please note: if you overload the wood burning stove and burn more than approx. 3.1 kg wood/hour, there is a risk

that the lacquered surface of the stove will become discoloured and eventually fall off. The stove can be

resurfaced, but this is not covered by the manufacturer’s guarantee. In the same way, any other damage to the

stove caused by overloading will not be covered by the guarantee.

3.8 Aduro-tronic

The patent-applied Aduro-tronic is designed to operate the stove for you. All you have

to do is put dry wood in the stove, and activate the control system - Aduro-tronic does

the rest, leaving you to enjoy the flames and the benefits of efficient combustion.

Aduro-tronic is a patent-applied mechanical solution, which works without the use of

electricity.

Please note: Use of dry wood of the right size is important to achieve optimum

combustion.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aduro 9-4 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Aduro 9-4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info