Bedienungsanleitung Aduro Asgard 6 (Seite 20 von 33) (Deutsch, Englisch, Dänisch, Französisch, Schwedisch)

632367

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

_______________________________________________________________________________________________________________________________

- 20 -

In order to reduce the risk of ash falling from the stove when the door is opened to add more fuel, it is a good idea

to open the primary air intake/damper for approx. 1 minute before the door is opened. This increases the draught

through the stove and reduces the risk that ash will drop on the floor.

Please note: if you overload the wood burning stove and burn more than approx. 2.5 kg wood/hour, there is a risk

that the lacquered surface of the stove will become discoloured and eventually fall off. The stove can be resurfaced,

but this is not covered by the manufacturer’s guarantee. In the same way, any other damage to the stove caused by

overloading will not be covered by the guarantee.

3.8 Ventilation/fresh air supply

In order for the wood burning stove to function at optimum efficiency, air is needed for the combustion process.

There must be sufficient fresh air coming into the room containing the wood burning stove. In very well-insulated

houses, or houses with powerful cooker hoods and/or air conditioning systems, a vacuum can be created around

the stove, leading to smoke leakage and poor combustion. In these circumstances, it might be necessary to open a

window to provide air for combustion and to equalize the vacuum. Alternatively, you could fit an air vent in the room

containing the wood burning stove. The amount of air needed for combustion is 25 m

/h.

4.0 The chimney

Data for chimney calculation:

Wood

Flue temperature at [20 C]

273

Chimney draught at testing power

[mbar]/[Pa]

0.12/12

Flue gas mass flow [g/s]

5,5

The optimum combustion is achieved at a constant chimney draught of 0.10 to 0.14 mbar measured in the flue pipe

above the stove. There are many factors that affect the chimney draught, including the outside temperature, wind

strength and surrounding buildings. If it is impossible to establish a sufficiently natural chimney draught, the chimney

can be fitted with a smoke extractor. If the chimney draught is too strong, a damper can be fitted to regulate the

chimney draught. Contact your local chimney sweep for more advice.

There are no requirements with respect to specific chimney heights, but a chimney must be tall enough to provide a

good draught – above 12 Pa. If the recommended chimney draught is not achieved, there may be problems with

smoke out of the door by firing.

4.1 Inadequate draught in the chimney

If the chimney is too short, leaks or is inadequately insulated, there may be problems with the chimney draught (let

the chimney sweep assess this). The draught should be approx. 0.10–0.14 mbar in order to provide satisfactory

combustion and prevent smoke leakage.

If the chimney sweep judges the draught to be satisfactory, but you still have problems lighting a fire, try extending

the fire lighting phase/using more thin pieces of kindling, so that the chimney gets thoroughly warm. The chimney

will not draw at optimum effect until it is warm. The fire lighting phase can be prolonged by using a lot of kindling

and 1-2 firelighters. When a layer of embers has been formed, add 2–3 dry logs.

5.0 Maintaining and cleaning your wood burning stove

Gaskets

With time, the gaskets will wear, and, in order to avoid wild combustion, they must be replaced as required.

Glass

If the wood you burn is too moist, you will get soot stains on the glass pane. They can be easily removed using a

damp cloth that you dip in cold ash and rub on the sooty glass. Special cleaning agents are also available to remove

soot from glass, i.e. the Aduro Easy Clean pad.

Combustion chamber

The yellow tiles in the combustion chamber eventually wear out and they should be replaced when the cracks are

more that 0.5 cm. The durability of the tiles will depend on how often and how intensively the stove is used. You can

change the tiles yourself. They are available as a ready-to-use set. You can also buy one-piece tiles that you can

cut to the size of the worn plates yourself. Please visit www.aduroshop.com.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aduro Asgard 6 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info