636052
61
Zoom out
Zoom in
Vorherige Seite
1/266
Nächste Seite
4.5.1 Unconnected Packets
In order to allow amateurs to send message beacons and to call CQ, the
AX.25 protocol has the ability to send packets that are intended for
more than one specific packet station to see. Since all packets must
have a destination "callsign", the PK-232 sends Unprotocol packets TO
the callsign of CQ. This can be changed with the UNPROTO command, but
most people like this since it makes an easy way to call CQ.
4.5.2 Connected Packets
When you Connect to another station, the AX.25 packet protocol ensures
that the station to whom you are connected receives all the packets
that you send. Similarly, the protocol ensures you will receive all
the packets that the other station sends to you. The following
describes briefly how the protocol does this.
4.5.3 FRACK and RETRY
When the PK-232 is connected and sends a packet to another station, it
expects an acknowledgment (ACK) packet from the other station to
confirm that the packet was received. The AX.25 packet protocol will
automatically retransmit (retry) packets when an acknowledgment is not
received from the distant end of the link within a specified time.
The FRACK command (FRame ACKnowledge time) sets the time lapse allowed
before the originating station retransmits (retries) the packet.
The RETRY command sets the maximum number of retransmissions before
the sending station terminates the connection (DISCONNECTS).
The TRIES counter keeps track of the retries that have occurred on the
current packet.
4.5.4 PACLEN and MAXFRAME
Packets will be sent either when the <Enter> key is pressed or when
the maximum packet size is exceeded. The maximum packet size is set
by the PACLEN command which defaults to 128 characters. When large
amounts of data need to be sent, this value can be increased to 256.
When conditions are poor or the channel is crowded as on HF packet,
this value should be reduced to 64 or less.
The packet protocol allows more than one frame to be sent in a single
transmission. The default is set to 4 by the MAXFRAME command. When
conditions are good up to 7 frames can be sent to speed data transfer.
When conditions are poor or the channel is crowded, MAXFRAME should be
reduced to only 1 frame.
4.5.5 Reducing Errors through Collision Avoidance
If every packet station could hear every other station, there would be
very few "collisions" due to stations transmitting at the same time.
Since packet operates over the radio, there are usually many stations
operating on the same frequency that cannot hear each other. The
digipeaters and network nodes allow these stations to communicate with
each other, but this increases the chances of collisions.
4/91 4-20
61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für AEA PK-232 MBX - Pakratt 232 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von AEA PK-232 MBX - Pakratt 232

AEA PK-232 MBX - Pakratt 232 Bedienungsanleitung - Englisch - 199 seiten

AEA PK-232 MBX - Pakratt 232 Bedienungsanleitung - Englisch - 217 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info