Bedienungsanleitung AEE MagiCam SD21G (Seite 18 von 36) (Englisch)

551553

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

aee.com

-15-

Operations

1. Insert a Micro SD card into the SD21 video camera.

Note: Use a branded Micro SD card, for example, Transcend Class 10 memory card.

2. Powering on the SD21 Video camera

Turn the power switch to the ON position to power on the SD21 video camera. At this time, the red indicator is on, and

the SD21 video camera changes to the preview state.

Note:

a. If the battery power is low, the” “symbol is displayed on the TFT screen together with a promot.

b. If no Micro SD card is inserted, no symbol is displayed in the bottom-right corner of the TFT screen.

3. Recording a Video

In the preview state, press the ”Video” key to start video recording. The video recording duration is displayed in the

upper-right part of the TFT screen. The "Video/Audio indicator (green)" and the "Video/Photo indicator (green)" on the

top of the video camera blink slowly. The recording duration is correctly displayed on the LCD segment screen. During

video recording, the video camera responds only to operations for the zoom in (+) and zoom out (–) keys. Press the

“Stop” key once to stop and save the currently recorded video file, and the video indicator (green) on the front side is

off. The video camera restores to the preview state. The recording duration disappears on the LCD segment screen.

Note:

a. During video recording, turn the power switch to the “OFF” position to power off the video camera after saving the

currently recorded file.

b. During video recording, if the battery power runs low, the system saves the currently recorded file and enters standby

mode, displaying a prompt of “Low battery ” on the TFT screen, until the video camera is powered off.

c. During video recording, if the Micro SD card is full, the system saves the currently recorded file. The system also displays

a message “Card full” on the TFT screen, indicating that the Micro SD card is full. In addition, the duration for video

recording stops on the LCD segment screen, and the system restores to the preview state.

d. In cyclic recording mode, the system automatically saves a file every 15 minutes. (The cyclic recording function and the

pre-video function cannot be simultaneously enabled.)

e. If the D23 backup battery is provided and fully recharged, the video camera can continuously record video programs

for about four hours and record audio programs for about seven hours.

f. In WVGA/100 and WVGA/120 modes, the video camera does not support the time display, zooming, and 180° photo

rollover functions. In 1080i/50 and 1080i/60 modes, the video camera does not support the time display function.

g. In audio recording mode, the volume cannot be adjusted by pressing the “+” or “–” key. In playback, however, the

volume can adjusted by pressing the “+” or “–” key.

h. If the video camera provides a TFT screen and is in the preview state, after using a HDMI patch cord to connect the video

camera to a HD display device, you can perform basic operations for the video camera on the HD display device (These

basic operations, however, cannot be performed if no TFT screen is available on the video camera).

4. Taking a Picture

Before taking a picture, perform the following operations to set the image resolution.

— Press the “M” key to display the setup interface.

— Press the “>” key to display the camera setup interface ( ).

— Press the “+” or “–” key and choose “Image Resolution”.

— Press “OK” to display the resolution setup menu.

You can set the resolution to any of the following three modes:

3M, with an image resolution of 2048 x 1536.

5M, with an image resolution of 2592 x 1944.

8M, with an image resolution of 3200 x 2400.

Four photo shooting modes are available for the video camera.

a. single shot (the default mode)

In the preview state, press the “Photo” key once to take a picture while the system generates a click tone. The green

indicator on the front side of the video camera also blinks once (the shooting icon on the LCD segment screen blinks

once), and the video camera restores to the preview state.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEE MagiCam SD21G Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AEE MagiCam SD21G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info