18 19
BS 18C BSB 18C
...........................
...........................
..............................-
.............................
......................0-450
-1
-1
....................0-1650
-1
-1
..............................-
-1
...........................
...........................
.....................1,5-13
..........................
..........................
...........................
...........................
..............................-
2
..............................-
2
..........................
2
.........................
2
..........................
2
.........................
2
..........................
2
.........................
2
..........................
2
.........................
2
ENGLISH
EC-DECLARA
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 60745, EN 55014-1, EN 55014-2, in
accordance with the regulations 2006/42/EC, 2004/108/EC
Winnenden, 201
Rainer Kumpf
Manager Product Development
Authorized to compile the technical le
BA
New battery packs reach full loading capacity after 4 - 5
chargings and dischargings. Battery packs which have not
been used for some time should be recharged before use.
T
performance of the battery pack.
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
T
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BA
The battery pack has overload protection that protects it
from being overloaded and helps to ensure long life.
Under extreme stress the battery electronics switch off the
machine automatically
and then on again. If the machine does not start up again,
the battery pack may have discharged completely
case it must be recharged in the battery charger
MAINTENANCE
Use only
components need to be replaced which have not been
described, please contact one of our
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the
printed on the label and order the drawing at your local
service agents or directly at:
Max-Eyth-Straße 10, D-71364 Winnenden, Germany
SYMBOLS
Please read the instructions carefully before
starting the machine.
Remove the battery pack before starting any
work on the machine.
Do not dispose of electric tools together with
household waste material! In observance of
European Directive 2002/96/EC on waste
electrical and electronic equipment and its
implementation in accordance with national law
electric tools that have reached the end of their
life must be collected separately and returned to
an environmentally compatible recycling facility
ENGLISH
TECHNICAL DA Cordless percussion drill/driver
Drilling capacity in steel
Drilling capacity in wood
Drilling capacity in brick and tile
Wood screws (without pre-drilling)
No-load speed 1st gear
No-load speed 2nd gear
Rate of percussion under load max.
T
Battery voltage.........................................................................
Drill chuck range
Weight according EPT
Weight according EPT
Noise/vibration information
Measured values determined according to EN 60 745.
T
Sound pressure level (K
Sound power level (K
Wear ear protectors!
T
determined according to EN 60745.
Vibration emission value a
h
Impact drilling into concrete
Uncertainty K=
Drilling into metal
Uncertainty K=
Screwing
Uncertainty K=
*1 Measured according to
W
instructions, including those given
brochure. Failure to follow the warnings and instructions
may result in electric shock, re and/or serious injury
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Wear ear protectors when impact drilling. Exposure to
noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a „live“ wire may make exposed metal parts of the power
tool „live“ and could give the operator an electric shock.
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Sawdust and splinters must not be removed while the
machine is running.
When working in walls ceiling, or oor
electric cables and gas or waterpipes.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household
refuse or by burning them.
old batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System GBS chargers for charging System GBS
battery packs. Do not use battery packs from other systems.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of contact
with battery acid wash it off immediately with soap and
water
minutes and immediately seek medical attention.
SPECIFIED CONDITIONS OF USE
The electronic battery percussion drill/screwdriver may be
used for drilling, percussion drilling, as well as screwdriving
for independent use away from mains supply
Do not use this product in any other way as stated for
normal use.
W
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signicantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
