Bedienungsanleitung AEG CSFMP200 (Seite 43 von 54) (Deutsch, Englisch)

28801

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

OPERATION

SWITCHING ON/OFF THE UNIT

Switch on the unit by pressing any

button [except OPEN button (7) and

button (4)]. When system is on ,press

button (9) to turn off the unit.

Volume Bass Treble Balance Fader

FACEPLATE RELEASE

Press OPEN button (7) to detach the

removable faceplate.

SOUND ADJUSTMENT

Press SEL button (10) to select the

desired adjustment mode. The

adjustment mode will change in the

following order:

By pressing the volume up button (11)

or volume down button (12), it is

possible Press SEL button (10) for

several seconds, it is activated as

cyclical mode of following functions for

user’s selection.

TA SEEK or ALARM

PI SO UND or MUTE

MASK DPI or ALL RETUNE L or S

BEEP 2'nd or OFF

a) TA SEEK OR TA ALARM

- TA SEEK mode:

When newly tuned station does not

receive TP information for several

seconds, the radio retunes to next

station which has not the same

station (PI) as the last station, but

has the TP information.

When TP information gets lost at the

current station for retune time which

is set by RETUNE SHORT (30 sec.)

or RETUNE LONG (90 sec.), the

radio start to retune to next same PI

station. When same PI station does

not catch in 1 cyclic search, the

radio retunes to next station with TP

information.

- TA ALARM mode:

When this mode is selected, any

automatic retune mode is not

activated. Only double beep sound

(ALARM) is output.

When newly tuned station does not

have TP information for several

seconds, beeps come out.

When TP information gets lost at the

current station for retune time, the

beep sound is out-putted.

When newly tuned station has no

RDS signal, "PI SEEK" is

suppressed somewhat.

b) PI SOUND or PI MUTE

While AF switching is implemented in

C201 station, AF can switch to 100

MHz, which is non genuine AF (where,

different PI with same AF) in short

"DIP".

If a car cruises that critical area back

and forth, an oscillation

phenomenon can be occurred,

because the different PI code can be

received from 100 MHz with "XXX"PI.

The car radio has special procedure

to reduce even this kind of

unavoidable situation however there

is a limit to be escaped from this

serious case perfectly.

In that serious case, 2 mode is

selectable as follows:

100

PI:C201

PI:XXX

- PI SOUND mode:

When above different PI sound (DIP)

is heard once in a while, the DIP's

sound will be heard for a short time.

- PI MUTE mode:

Under above same situation, a mute

sound will be heard for a short time.

c) RETUNE L or RETUNE S mode

The initial time of automatic TA search

or PI search modes is selected.

When PI information is not caught for

retune time, the radio starts to retune

to next same PI station.

When same PI station does not catch

1 cyclic search, the radio goes to last

station and waits for several minutes

until PI code is received.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG CSFMP200 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info