Bedienungsanleitung AEG DB 130 97212 (Seite 10 von 32) (Deutsch, Englisch, Französisch, Italienisch)

574024

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

1918

ASSEMBLY AND CONNECTION

Model DB 130

Connecting to a 12-V vehicle socket:

1. Insert the vehicle plug [10] into the 12 V vehicle socket.

2. Place the double plug socket in such a way that the unit or the cable does

not hinder the driver.

Model DH 200

Connecting to the vehicle battery:

The DH 200 model is connected directly to the battery with the ring terminal

connector cable.

Warning! The connecting cable from the double plug socket must run through

the interior of the vehicle. This is usually achieved by running it along a section

of vehicle body panelling.

If you are unable to run the cable through the interior of the vehicle yourself,

take the job to a vehicle repair shop.

▪

If the connecting cable has to be led through sharp or rough walls (e.g.,

metal panels), use rubber grommets or cable channels to avoid damage to

the cable.

▪

Lay and fasten the cable in such a way that it cannot come into contact with

any movable, hot or sharp-edged parts.

1. Place the double plug socket in such a way that you are not hindered by

the unit or the cable whilst driving.

2. Lead the double plug socket connecting cable from the vehicle interior to the

battery.

3. Connect the terminal connection cable (red ring connection) (+) [6] to the

positive terminal on the battery.

4. Connect the terminal connection cable (black ring connection) (-) [5] to the

negative terminal on the battery.

5. Connect the comfort connection plugs [8] with one another.

OPERATION

Model DB 130

As soon as the vehicle plug [10] is connected with the 12 V vehicle socket and

is conducting an electrical charge, the red LED will illuminate. Now the double

plug socket is ready for use and devices can be connected to both 12 V vehic-

le sockets, as well as to the USB connection socket.

Note that with some vehicles, the 12 V vehicle socket may only function when

the ignition is switched on.

Use the double plug socket for a short time only if the vehicle engine is not

switched on. Failure to ob-serve this can cause the vehicle battery to run down.

After use, always remove the plug from the 12 V vehicle socket. When remo-

ving the connection, pull on the plug itself, and never on the connecting cable.

Model DH 200

To switch the unit on, switch the ON/OFF switch [4] on the double plug socket

to ON. Now the double plug socket is ready for use.

▪

Make sure that the total power consumption connected to the double plug

socket does not exceed 15 A.

Voltage Indicator LED functions [3]:

Red Current < 10.5 V

Yellow Current between 10.5 V-12.5 V

Green Current > 12.5 V

Battery monitor function: As soon as the double plug socket is switched on, an

LED illuminates which corresponds to the battery voltage. If the battery voltage

sinks below 10.5 V, the LED will light up red. If this happens, the double plug

socket will automatically switch off in order to prevent the vehicle battery from

running down. This will resume if the battery return to 11.8 V or above.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG DB 130 97212 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info