Bedienungsanleitung AEG DDLE Basis 13 (Seite 19 von 76) (Deutsch, Englisch, Holländisch, Französisch)

648332

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Operation – for users and qualied contractors

2.4 Test symbols

See type plate on the appliance.

Country-specic approvals and certications:

Germany

A general test certicate as verication of suitability re-

garding noise emissions has been issued for this appli-

ance, based on the State Building Regulations [Germany].

AEG

HOL

DIN 4109

PA-IX 6814/I

3. Appliance description

The electronically controlled instantaneous water heater

with automatic output matching keeps the outlet temper-

ature constant up to the output limit. The temperature is

then selected via the draw-off tap.

Heating system

The bare wire heating system has a pressure-tested plas-

tic casing. The heating system is suitable for hard and soft

water areas. This heating system has a low susceptibility

to scale build-up. This system ensures rapid and efcient

DHW availability.

Note

The appliance is equipped with an air detector that

largely prevents damage to the heating system. If,

during operation, air is drawn into the appliance,

the appliance shuts down for one minute, thereby

protecting the heating system.

4. Settings

The DHW outlet temperature can be variably adjusted.

Hand wash basin (approx.

35 °C)

Shower (approx. 40 °C)

Bath (approx. 45 °C)

Kitchen sink (approx. 55 °C)

» Turn the temperature selector to the required

temperature.

Temperature limit

Your qualied contractor can set a temperature limit of up

to 43 °C inside the appliance. With the temperature limit

enabled you can turn the temperature selector across its

full range. You can now set the outlet temperature only

between 30 °C and 43 °C.

Note

Should the outlet temperature fail to reach the re-

quired level with the draw-off valve fully open and

the temperature selector set to maximum, then more

water is owing through the appliance than can be

heated by the heating system. The appliance is at

its output limit.

» Reduce the water volume at the draw-off valve.

Recommended setting for operation with a

thermostatic valve

Set the temperature at the appliance to the maximum

temperature.

Following an interruption of the water supply

Material losses

In order to prevent the destruction of the bare wire

heating system, return the appliance into use follow-

ing an interruption of the water supply as follows:

» Disconnect the appliance from the power sup-

ply by removing the fuses/tripping the MCBs.

» Open the tap for one minute until the appliance

and its upstream cold water inlet line are free of

air.

» Switch the mains power back ON again.

5. Cleaning, care and

maintenance

» Never use abrasive or corrosive cleaning agents. A

damp cloth is sufcient for cleaning the appliance.

» Check the taps regularly. Limescale deposits at the

tap outlets can be removed using commercially avail-

able descaling agents.

6. Troubleshooting

Problem Cause Remedy

The appliance will not

start despite the DHW

valve being fully open.

There is no voltage at

the appliance.

Check the fuses/

MCBs in your fuse

box/distribution panel.

The flow rate is too

low. The aerator in

the tap or the shower

head is scaled up or

contaminated.

Clean and/or descale

the aerator or shower

head.

Required tempera-

ture > 45 °C is not

achieved.

The water supply has

been interrupted.

Vent the appliance

and the cold water

inlet line (see chapter

"Operation / Set-

tings").

The cold water

inlet temperature is

> 45 °C.

Reduce the cold water

inlet temperature.

If you cannot remedy the fault, notify your qualied contractor.

To facilitate and speed up your enquiry, please provide the serial

number from the type plate (000000-0000-00000):

Nr.: 000000-0000-00000

D0000041614

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG DDLE Basis 13 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info