Bedienungsanleitung AEG DDLE Basis 13 (Seite 24 von 76) (Deutsch, Englisch, Holländisch, Französisch)

648332

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Installation – for qualied contractors

10.2 Installation options

10.2.1 Electrical connection from below on

unnished walls

L1í

X11

26_02_02_0767

» Fit the cable grommet.

Material losses

If you break out the wrong knock-out by mistake, use

a new back panel.

» Break out the cable grommet knock-out in the

back panel. Deburr the sharp edges with a le if

necessary.

» Reposition the mains terminal in the appliance from

the top to the bottom.

» Push the back panel over the threaded stud and the

cable grommet. Pull the cable grommet by the lock-

ing hooks into the back panel using pliers, until both

locking hooks audibly click into place.

» Push the back panel rmly against the wall. Lock the

xing toggle by turning it 90° clockwise.

10.2.2 Electrical connection on nished walls

Note

This type of connection changes the protection rat-

ing of the appliance.

» Change the type plate. Cross out "IP 25" and

mark the box "IP 24". Please use a ballpoint pen

to do this.

Material losses

If you break out the wrong knock-out by mistake, use

a new back panel.

» Cleanly cut or break out the required opening in the

appliance back panel (see chapter "Installation /

Specication / Dimensions and connections"). De-

burr the sharp edges with a le if necessary.

» Route the power cable through the cable grommet

and connect it to the mains terminal.

10.2.3 Connecting a load shedding relay

Install a load shedding relay in the distribution board in

conjunction with other electric appliances, e.g. electric

storage heaters. The relay responds when the instanta-

neous water heater starts.

Material losses

Connect the phase that switches the load shedding

relay to the indicated terminal of the mains terminal

in the appliance (see chapter "Installation / Speci-

cation / Wiring diagram").

10.2.4 Undersink installation, water connections –

from above

An undersink installation with water connections from

above can be achieved with an additional pipe assembly

for undersink appliances. Cleanly break out the water pipe

knock-outs in the back panel and t the pipe assembly.

10.2.5 Water installation on nished walls

Note

This type of connection changes the protection rat-

ing of the appliance.

» Change the type plate. Cross out "IP 25" and

mark the box "IP 24". Please use a ballpoint pen

to do this.

26_02_02_0765

» Fit the water plugs with gaskets in order to seal the

connection for unnished walls.

» Fit a suitable pressure tap.

26_02_02_1006

» Click the lower section of the back panel into place in

the upper section of the back panel.

» Secure the connection pipes to the appliance.

» Secure the back panel at the bottom with two addi-

tional screws.

Material losses

If you break out the wrong knock-out by mistake, use

a new back panel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG DDLE Basis 13 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info