Bedienungsanleitung AEG DDLE LCD 27 (Seite 22 von 100) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

648345

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Installation - for qualied contractors

9.2 Water installation

◦ A safety valve is not required.

» Flush the water line thoroughly.

» Ensure that the ow rate (see chapter “Specication /

Data table”, On) for switching on the appliance is

achieved. If the ow rate is not achieved, remove the

ow limiter (see chapter “Installation / Removing the

ow limiter”).

» Increase the mains water pressure if the required

ow rate is not achieved with the draw-off valve fully

opened.

Taps

Use appropriate pressure taps. Open taps are not per-

mitted.

Note

Never use the shut-off valve in the cold water inlet

to reduce the ow rate. It is intended to shut off the

appliance.

Permissible water pipe materials

◦ Cold water inlet pipe:

Galvanised steel pipe, stainless steel pipe, copper

pipe or plastic pipe

◦ DHW outlet pipe:

Stainless steel pipe, copper pipe or plastic pipe

Material losses

If plastic pipework systems are used, take into ac-

count the maximum inlet temperature and the max-

imum pressure (see chapter “Specication / Data

table”).

Flexible water connection lines

» If the appliance is installed with exible water con-

nection lines, ensure that the bayonet ttings of

the pipe bends do not become twisted inside the

appliance.

» Secure the back panel at the bottom with two addi-

tional screws.

10. Installation

10.1 Standard installation

◦ Electrical connection from above; installation on un-

nished walls

◦ Water connection, installation on unnished walls

◦ DDLE LCD 18/21/24: Connected load 21 kW preset

For further installation options, see chapter “Installation

alternatives”:

◦ Electrical connection from below on unnished walls

◦ Electrical connection for nished walls

◦ Connecting a load shedding relay

◦ Undersink installation, water connections – from

above

◦ Water installation for nished walls

◦ Operation with preheated water

◦ Temperature limit

Opening the appliance

D0000041615

» Open the appliance by releasing the snap lock.

T-

26_02_02_0762

» Remove the back panel by pressing the two locking

hooks and pulling the lower part of the back panel

forwards.

Preparing the power cable

160

≥ 30

26_02_02_0887

Fitting the wall mounting bracket

26_02_02_0972

» Mark out the holes for drilling with the installation

template. If the appliance is to be installed with water

connections on nished walls, also mark out the x-

ing holes on the lower part of the template.

» Drill the holes and secure the wall mounting bracket

with 2 screws and 2 rawl plugs (screws and rawl

plugs are part of the standard delivery).

» Fit the threaded stud provided.

» Mount the wall mounting bracket.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG DDLE LCD 27 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info