Bedienungsanleitung AEG DDLE LCD 27 (Seite 25 von 100) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

648345

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Installation - for qualied contractors

» Reposition the mains terminal in the appliance from

the top to the bottom.

» Push the back panel over the threaded stud and the

cable grommet. Pull the cable grommet by the lock-

ing hooks into the back panel using pliers, until both

locking hooks audibly click into place.

» Press the back panel rmly into place and lock the

xing toggle by turning it clockwise through 90°.

10.2.2 Electrical connection for nished walls

Note

This type of connection changes the protection rat-

ing of the appliance.

» Change the type plate. Cross out “IP 25” and

mark the box “IP 24”. Please use a ballpoint pen

to do this.

Material losses

If you break out the wrong knock-out by mistake, you

should use a new back panel.

» Cut or break out the required entries in the back

panel cleanly (for positions, see chapter “Speci-

cation / Dimensions and connections”). Deburr the

sharp edges with a le if necessary.

» Route the power cable through the cable grommet

and connect it to the mains terminal.

10.2.3 Connecting a load shedding relay

Install a load shedding relay in the distribution board in

conjunction with other electric appliances, e.g. electric

storage heaters. The relay responds when the instanta-

neous water heater starts.

Material losses

Connect the phase that switches the load shedding

relay to the indicated terminal of the mains terminal

in the appliance (see chapter “Specication / Wiring

diagram”).

10.2.4 Undersink installation, water connections –

from above

An undersink installation with water connections from

above can be achieved with the additional pipe assembly

for undersink appliances. Cleanly break out the water pipe

knock-outs in the back panel and t the pipe set.

10.2.5 Water installation for nished walls

Note

This type of connection changes the protection rat-

ing of the appliance.

» Change the type plate. Cross out “IP 25” and

mark the box “IP 24”. Please use a ballpoint pen

to do this.

26_02_02_0765

» Fit water plugs with gaskets to seal the connection

on unnished walls.

» Fit a suitable pressure tap.

26_02_02_1006

» Click the lower part of the back panel into place in

the upper part of the back panel.

» Secure the connection pipes to the appliance.

» Secure the back panel at the bottom with two addi-

tional screws.

Material losses

If you break out the wrong knock-out by mistake, you

should use a new back panel.

» Cleanly break out the knock-outs in the appli-

ance cover. Deburr the sharp edges with a le if

necessary.

» Push the lower part of the back panel under the con-

nection pipes of the tap and click the lower part of

the back panel into place.

» Secure the connection pipes to the appliance.

10.2.6 Operation with preheated water

You can limit the maximum inlet temperature by installing

a central thermostatic valve.

10.2.7 Temperature limit

CAUTION Burns

If operating with preheated water, the set tempera-

ture limit and anti-scalding protection may be inef-

fective.

» In this case, limit the temperature with an up-

stream central thermostatic valve.

You can set the temperature limit inside the appliance

cover to 43 °C.

D0000041912

» Switch the temperature limit to 43 °C.

After enabling the temperature limit, you can only select

temperatures between 30 and 43 °C.

10.3 Completing the installation

» Open the shut-off valve in the twin connector or the

cold water inlet line.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG DDLE LCD 27 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info