Bedienungsanleitung AEG DDLE OKO TD 18 (Seite 35 von 100) (Deutsch, Englisch)

648347

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Installation – for qualied contractors

9.3 Installation versions

9.3.1 Power supply - unnished walls - from below

26_02_02_0890

» Push the cable grommet over the power cable (1).

» Break out the cable grommet knock-out in the back

panel (2).

» Reposition the mains terminal from the top to the

bottom. For this, undo the screw and ret the mains

terminal to the bottom; then retighten the mains

terminal (3).

» Push the back panel over the threaded stud and the

cable grommet. Pull the cable grommet at the taps

into the back panel using pliers, until both locking

hooks audibly click into place (4).

» Push the back panel rmly and ush against the wall

and lock with the xing toggle (5).

9.3.2 Power supply - nished walls

Cut a cable entry point into the back panel for the power

cable or break out the appropriate knock-out.

325

b03

b02

b04

D0000019778

b02 Entry electrical cables 1

b03 Entry electrical cables 2

b04 Entry electrical cables 3

Note

With power supply on nished walls, the protection

rating is reduced to IP 24 (splashproof).

Mark the type plate with a permanent marker:

Cross out „IP 25“ and mark the box „IP 24“.

9.3.3 Priority control

When used in conjunction with other electrical appliances,

e.g. electric storage heaters, the load shedding relay can

be used. The load shedding relay LR 1-A must be installed

on a top-hat rail inside the distribution area.

LR 1-A

85_02_02_0003

1 Load shedding relay (see “Special accessories”).

2 Control cable to the contactor of the second

appliance (e.g. electric storage heater).

3 Control contact, opens when switching the

instantaneous water heater ON.

The relay trips as soon as the instantaneous water heater

starts.

Only connect the load shedding relay to the central phase

of the mains terminal.

9.3.4 Undersink installation, water connections

from the top

Undersink installation with water connections from the

top can be achieved with the additional pipe assembly

for undersink appliances. For this, cleanly break out the

apertures for the water pipes in the back panel and t the

pipe assembly.

9.3.5 Tap for nished walls

The pressure tap for nished walls is offered as special

accessory; see chapter “Special accessories”. For

installation, carry out the following steps:

» Fit the water plugs G ½” with gaskets to the

appliance water connections. The plugs are part of

the standard delivery of the tap.

» Install the tap.

» Push the free ends of the pipes into the valve.

» Click the lower part of back panel.

» Secure the connection pipes to the appliance.

» Cleanly break out the entries in the appliance cap

(1). If necessary, use a le.

» Secure the back panel at the bottom with two

additional screws (24).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG DDLE OKO TD 18 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info