Bedienungsanleitung AEG Electrolux DB 1100 (Seite 12 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

112987

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

• Please check the mains cord from time

to time for damage! Special tools are

required to repair a damaged mains

cord. If the supply cord is damaged, it

must be replaced by the manufacturer,

its service agent or similarly qualified

persons in order to avoid a hazard.

Repairs to this appliance may only be

carried out by qualified service engi-

neers. Considerable danger may result

from improper repairs. If repairs

become necessary, please contact the

Customer Care Department or your

authorised dealer.

Technical Data

Power consumption: 1600 - 2000 W

Mains voltage: 220 - 240 V

;

This appliance conforms with the fol-

lowing EC Directives:

• Low Voltage Directive 2006/95/EC

• EMC Directive 89/336/EEC with

amendments 92/31/EEC and

93/68/EEC

Using for the First Time

Setting the Temperature

(Figure 2)

Please note the internationally appli-

cable care symbols on garment labels.

On good quality garments they indi-

cate the correct ironing temperatures.

The ironing table indicates which tem-

perature is most appropriate for a par-

ticular type of fabric. We recommend

sorting the washing first. Start with

materials that require low temperature

ironing (e.g. PERLON). Follow on by

ironing materials that require progres-

sively higher temperatures. In this way

you avoid damaging sensitive fabrics

by using too high a temperature. When

switched on, the power indicator lamp

lights up (Figure 1/J); it goes out when

the temperature set has been reached.

However, if the temperature selector

(Figure 1/N) is turned back, please note

that it takes a while for the soleplate

to cool down. Only when the power

indicator light comes on again has the

soleplate reached the cooler tempera-

ture.

Dry Ironing

0 Set the steam selector (Figure 1/F) to

position

„“ (Figure 4/A).

0 Turn the temperature selector

(Figure 1/N) to the desired tempera-

ture.

Steam Ironing

Filling the Steam Iron (Figure 3)

The water reservoir should only be

filled when the plug has been removed

from the socket.

0 Set the steam selector to position

„“= dry iron (Figure 4/A) and hold

the appliance upright.

0 Fill the water reservoir at most to the

“MAX” mark. To do this, you can use

the measuring beaker supplied

(Figure 1/P).

Water Quality

You can use tap water up to 3 mmol/I

17° dH water hardness level. Your local

Water Authority can advise you on the

hardness of the water in your area. If

the water from your tap is harder than

the above, please use distilled water

available from a chemist or a 50:50

mixture of tap water and distilled

water.

When using for the first time,

please note:

0 Fill the reservoir with water; set the

steam selector (Figure 1/F) to maxi-

mum position (Figure 4/B).

0 Heat the appliance and place it with

the soleplate facing downwards on an

iron rest or plate (Figure 5) to allow the

water to steam through and activate

the steam chamber.

822 949 340 DB_1100.book Seite 12 Montag, 28. April 2008 11:51 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG Electrolux DB 1100 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info