Bedienungsanleitung AEG Electrolux HG995440XB (Seite 59 von 64) (Französisch)

462868

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ue with the gas connection. The flexible

pipe is prepared for apply when:

– it can not get hot more than room

temperature, higher than 30°C;

– it is no longer than 1500 mm;

– it shows no throttles;

– it is not subject to traction or torsion;

– it does not get in touch with cutting

edges or corners;

– it can be easily examined in order to

check its condition.

The control of preservation of the flexi-

ble pipe consists in checking that:

– it does not show cracks, cuts, marks of

burnings on the two ends and on its

full length;

– the material is not hardened, but

shows its correct elasticity;

– the fastening clamps are not rusted;

– expired term is not due.

If one or more defects are visible, do not

repair the pipe, but replace it.

When installation is complete,

make sure that the seal of each

pipe fitting is correct. Use a

soapy solution, not a flame!

8.2 Injectors replacement

Remove the pan supports.

Remove the caps and crowns of the

burner.

With a socket spanner 7 remove the

injectors and replace them with the

ones which are necessary for the

type of gas you use (see table in

"Technical Information" chapter).

Assemble the parts, follow the same

procedure backwards.

Replace the rating plate (it is near

the gas supply pipe) with the one for

the new type of gas supply. You can

find this plate in the package sup-

plied with the appliance.

If the supply gas pressure is changeable

or different from the necessary pressure,

you must fit an applicable pressure ad-

juster on the gas supply pipe.

8.3 Adjustment of minimum

level

To adjust the minimum level of the burn-

ers:

Light the burner.

Turn the knob on the minimum posi-

tion.

Remove the knob.

With a thin screwdriver, adjust the

by-pass screw position.

The by-pass screw

• If you change from natural gas G20/

G25 20/25 mbar to liquid gas, fully

tighten the by-pass screw in.

• If you change from liquid gas to natu-

ral gas G20/G25 20/25 mbar, undo the

by-pass screw approximately 1/4 of a

turn (1/2 of a turn for Triple Crown

burner).

WARNING!

Make sure the flame does not go

out when you quickly turn the

knob from the maximum position

to the minimum position.

8.4 Electrical connection

• Ground the appliance according to

safety precautions.

• Make sure that the rated voltage and

type of power on the rating plate

agree with the voltage and the power

of the local power supply.

• This appliance is supplied with a mains

cable. It has to be supplied with a cor-

rect plug, able to support the load

marked on the rating plate. The plug

has to be fitted in a correct socket.

• Any electrical component must be in-

stalled or replaced by the Service

Force Centre technician or qualified

service personnel.

ENGLISH 59

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG Electrolux HG995440XB Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AEG Electrolux HG995440XB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info