Bedienungsanleitung AEG HC412001 (Seite 13 von 20) (Englisch)

652157

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

The hob should not be installed in a bed

sitting room with a volume of less than

20 m³. If it is installed in a room of

volume less than 5 m³ an air vent of

effective area of 100 cm² is required. If it

is installed in a room of volume between

5 m³ and 10 m³ an air vent of effective

area of 50 cm² is required, while if the

volume exceeds 11 m³ no air vent is

required.

However, if the room has a door which

opens directly to the outside no air vent

is required even if the volume is between

5 m³ and 11 m³.

If there are other fuel burning appliances

in the same room, B.S. 5440 Part 2

Current Edition, should be consulted to

determine the requisite air vent

requirements.

For appliances installed in the Republic

of Ireland please refer to the NSAI-

Domestic Gas Installation I.S. 813 Current

Editions Table Four.

Location

The hob may be located in a kitchen, a

kitchen/diner or bed sitting room (with a

volume greater than 20 m³), but not in a

bathroom or shower room.

The minimum distance combustible

material can be fitted above the hob in

line with the edges of the hob is 400 mm.

If it is fitted below 400 mm a space of 50

mm must be allowed from the edges of

the hob.

For appliances installed in the Republic

of Ireland please refer to NSAI- Domestic

Gas Installation I.S 813 Current Edition

Section 7- Permitted Locations of

Appliance.

8.3 Gas Connection

WARNING!

Any gas installation must be

carried out by a GAS SAFE

Make sure that, once the hob is installed,

it is easily accessible for the engineer in

the event of a breakdown.

The manufacturer will not accept liability,

should the above instructions or any of

the other safety instructions incorporated

in this instruction booklet be ignored.

On the end of the shaft, which includes

the R 1/2" threaded elbow, adjustment is

fixed so that the washer is fitted between

the components as shown in the

diagram. Screw the parts together

without using excessive force.

A. End of shaft with nut

B. Elbow

Connection to the gas supply should be

with either rigid or semi-rigid pipe, i.e.

steel or copper.

The connection should be suitable for

connecting to R 1/2 (1/2 BSP male

thread).

When the final connection has been

made, it is essential that a thorough leak

test is carried out on the hob and

installation.

Make sure that the main connection pipe

does not exert any strain on the hob.

If you use flexible metal pipes make sure

that they agree to ISO 10380 and ISO

10807 standards. Be careful they do not

come in touch with mobile parts or they

are not squeezed. Also be careful when

the hob is put together with an oven.

CAUTION!

It is important to install the

elbow correctly, with the

shoulder on the end of the

thread, fitted to the hob

connecting pipe.

CAUTION!

Failure to ensure the correct

assembly will cause leakage

of gas.

ENGLISH 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG HC412001 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AEG HC412001

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info