Bedienungsanleitung AEG HG654320NM (Seite 41 von 76) (Deutsch)

551908

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

8.2 Injectors replacement

Remove the pan supports.

Remove the caps and crowns of the

burner.

With a socket spanner 7 remove the

injectors and replace them with the

ones which are necessary for the

type of gas you use (see table in

"Technical Information" chapter).

Assemble the parts, follow the same

procedure backwards.

Replace the rating plate (it is near

the gas supply pipe) with the one for

the new type of gas supply. You can

find this plate in the package sup-

plied with the appliance.

If the supply gas pressure is changeable

or different from the necessary pressure,

you must fit an applicable pressure ad-

juster on the gas supply pipe.

8.3 Adjustment of minimum

level

To adjust the minimum level of the burn-

ers:

Light the burner.

Turn the knob on the minimum posi-

tion.

Remove the knob.

With a thin screwdriver, adjust the

by-pass screw position.

The by-pass screw

• If you change from natural gas G20/

G25 20/25 mbar to liquid gas, fully

tighten the by-pass screw in.

• If you change from liquid gas to natu-

ral gas G20/G25 20/25 mbar, undo the

by-pass screw approximately 1/4 of a

turn.

• If you change from natural gas G20/

G25 20/25 mbar to town gas G130 8

mbar, unscrew approximately 3/4 of a

turn.

• If you change from town gas G130 8

mbar to natural gas G20/G25 20/25

mbar screw approximately 3/4 of a

turn.

• If you change from liquid gas to town

gas G130 8 mbar unscrew approxi-

mately 1 turn.

WARNING!

Make sure the flame does not go

out when you quickly turn the

knob from the maximum position

to the minimum position.

8.4 Electrical connection

• Make sure that the rated voltage and

type of power on the rating plate

agree with the voltage and the power

of the local power supply.

• This appliance is supplied with a mains

cable. It has to be supplied with a cor-

rect plug which can hold the load that

the rating plate rates. Make sure that

you install the plug in a correct socket.

• Always use a correctly installed shock-

proof socket.

• Make sure that there is an access to

the mains plug after the installation.

• Do not pull the mains cable to discon-

nect the appliance. Always pull the

mains plug.

• There is a risk of fire when the appli-

ance is in connection with an exten-

sion cable, an adapter or a multiple

connection. Make sure that the

ground connection agrees with the

standards and regulations.

• Do not let the power cable to heat up

to a temperature higher than 90° C.

Make sure that you connect the blue

neutral cable to the terminal with a letter

"N" on it. Connect the brown (or black)

phase cable to the terminal which has a

letter "L". Keep the phase cable connec-

ted at all times.

8.5 Replacement of the

connection cable

To replace the connection cable use on-

ly H05V2V2-F T90 or equivalent type.

Make sure that the cable section is appli-

cable to the voltage and the working

ENGLISH 41

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG HG654320NM Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AEG HG654320NM

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info