Bedienungsanleitung AEG HG755421UM (Seite 14 von 20) (Englisch)

652633

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

5. Replace the rating plate (it is near the

gas supply pipe) with the one for the

new type of gas supply. You can find

this plate in the package supplied

with the appliance.

If the supply gas pressure is changeable

or different from the necessary pressure,

you must fit an applicable pressure

adjuster on the gas supply pipe.

8.5 Adjustment of minimum

level

To adjust the minimum level of the

burners:

1. Light the burner.

2. Turn the knob on the minimum

position.

3. Remove the knob.

4. With a thin screwdriver, adjust the

bypass screw position (A).

5. If you change:

• from natural gas G20 20 mbar to

liquid gas, fully tighten the bypass

screw in.

• from liquid gas to natural gas G20

20 mbar, undo the bypass screw

approximately 1/4 of a turn (1/2 of

a turn for Triple Crown burner).

WARNING!

Make sure the flame does

not go out when you quickly

turn the knob from the

maximum position to the

minimum position.

8.6 Electrical connection

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug (if applicable).

• The appliance must not be connected

with an extension cable, an adapter or

a multiple socket. There is a risk of

fire.

• Do not let the power cable to heat up

to a temperature of more than 90° C.

The cable should be guided by means

of clamps fixed to the side of the

cabinet, in order to avoid any contact

with the equipment beneath the

cooktop.

• Make sure that there is access to the

mains plug after the installation.

Electrical Requirements

Permanent electrical installation must

agree with the latest I.E.E. Regulations

and local Electricity Board regulations.

For your own safety the installation must

be done by a qualified electrician (e.g.

your local Electricity Board, or a

contractor who is on the roll of the

National Inspection Council for Electrical

Installation Contracting [NICEIC]).

The manufacturer refuses

to be held responsible, if

these safety measures are

not abided by.

Supply connections

This hob has to be connected to 220-240

V (~ 50/60 Hz ) electricity supply.

The hob has a terminal block which is

marked as follows:

• L — Live terminal

• N — Neutral terminal

• or E — Earth terminal

Before carrying out the connection,

make sure:

1. The limiter valve and the electrical

system can take the appliance load

(see the rating plate)

2. The supply system is equipped with

an efficient earth connection in

compliance with the current

standards and regulations

3. The outlet or omnipolar switch used

for connection is easily accessible

with the appliance installed.

The appliance is supplied with a 3 core

flexible power cable with a 3 amp plug. If

it is necessary to change the fuse, use a 3

amp ASTA-approved (BS 1362) fuse.

www.aeg.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG HG755421UM Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AEG HG755421UM

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info