Bedienungsanleitung AEG HG755450SY (Seite 8 von 20) (Englisch)

697944

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

B. Washer supplied with the appliance

C. Elbow supplied with the appliance

Liquid gas

Use the rubber pipe holder for liquid

gas. Always engage the gasket. Then

continue with the gas connection.

The flexible pipe is prepared for apply

when:

• it can not get hot more than room

temperature, higher than 30°C;

• it is no longer than 1500 mm;

• it shows no throttles;

• it is not subject to traction or torsion;

• it does not get in touch with cutting

edges or corners;

• it can be easily examined in order to

make sure its condition.

The control of preservation of the flexible

pipe consists in checking that:

• it does not show cracks, cuts, marks of

burnings on the two ends and on its

full length;

• the material is not hardened, but

shows its correct elasticity;

• the fastening clamps are not rusted;

• expired term is not due.

If one or more defects are visible, do not

repair the pipe, but replace it.

WARNING!

When installation is

complete, make sure that

the seal of each pipe fitting

is correct. Use a soapy

solution, not a flame!

3.3 Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the

burner.

3. With a socket spanner 7 remove the

injectors and replace them with the

ones which are necessary for the type

of gas you use (see table in

"Technical Data" chapter).

4. Assemble the parts, follow the same

procedure backwards.

5. Replace the rating plate (it is near the

gas supply pipe) with the one for the

new type of gas supply. You can find

this plate in the package supplied

with the appliance.

If the supply gas pressure is changeable

or different from the necessary pressure,

you must fit an applicable pressure

adjuster on the gas supply pipe.

3.4 Adjustment of minimum

level

To adjust the minimum level of the

burners:

1. Light the burner.

2. Turn the knob on the minimum

position.

3. Remove the knob .

4. With a thin screwdriver, adjust the

bypass screw position (A).

5. If you change:

• from natural gas G20 20 mbar to

liquid gas, fully tighten the bypass

screw in.

• from liquid gas to natural gas G20

20 mbar, undo the bypass screw

approximately 1/4 of a turn (1/2 of

a turn for Multi Crown burner).

WARNING!

Make sure the flame does

not go out when you quickly

turn the knob from the

maximum position to the

minimum position.

3.5 Electrical connection

• Make sure that the rated voltage and

type of power on the rating plate

agree with the voltage and the power

of the local power supply.

• This appliance is supplied with a

mains cable. It has to be supplied with

a correct plug which can hold the load

that the rating plate rates. Make sure

that you install the plug in a correct

socket.

• Always use a correctly installed

shockproof socket.

www.aeg.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG HG755450SY Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AEG HG755450SY

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info