Bedienungsanleitung AEG IDK84451IB (Seite 52 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

661926

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

3. Installation

The electrical and mechanical installation must be

performed by qualified personnel.

The household appliance is designed to be built-in to a

worktop (3-6 cm thick)

The minimum distance between the hob and the wall must be

at least 5cm at the front and at least 10 cm on the sides.

3.1 Electrical connection

Fig. 3

- Disconnect the device from the electrical network

-The installation must be performed by professionally qualified

personnel familiar with the applicable installation and safety

standards.

-The manufacturer declines any liability to people, animals or

things in the case of failure to follow the guidelines provided in

this chapter.

-The power cable must be long enough to allow removal of the

hob from the worktop

-Make sure that the voltage on the rating plate on the bottom

of the device corresponds to that of the house where it will be

installed.

-Do not use extension cords.

- Earthing is required by law

- The earth power cable must be 2cm longer than the other

cables

- If the household appliance is not equipped with a power

cable, use one with a minimum conductor diameter of 2.5

mm2 for power up to 7200 Watt; for higher power levels, the

diameter must be 4 mm2.

- At no point along the length of the cable must it reach a

temperature of 50° C above the room temperature.

- The device is intended to be permanently connected to the

electrical network, therefore, make the connection to the fixed

network via a standard omnipolar switch, which assures the

complete disconnection of the mains under category III over-

voltage conditions, and which is readily accessible after the

installation.

Note: to connect the appliance using the optional single

phase or three-phase connection, the existing cable must

be removed and replaced with another type (not supplied)

having the following specifications:

single phase connection: H05V2V2-F 3G4 cable

three-phase connection: H05V2V2-F 5G2.5 cable

Fig. 3b/3c

Caution! Before reconnecting the circuit to the mains power

supply and checking its correct operation, always check that

the network cable has been correctly assembled.

Caution! The interconnection cable must be replaced by

authorised customer service personnel or equally qualified

person.

3.2 Mounting

Before starting the installation:

• After unpacking the product, check that it has not been

damaged during transport and in the case of problems,

contact your dealer or Customer Service, before

proceeding with the installation.

• Check that the product is the right size for the installation

location.

• Check for accessories inside the packaging (placed there

for ease of transport) such as bags containing screws,

the warranty card, etc.. Remove them and keep them

safe.

• Also check that there is a power socket near the

installation area

Preparing the cabinet for installation:

- The product cannot be installed above cooling appliances,

dishwashers, heaters, ovens, washing machines and

dryers.

- Cut the cabinet before inserting the hob and carefully

remove shavings or sawdust.

IMPORTANT: use a single component adhesive sealant

(S), resistant against high temperatures up to 250°;

prior to installation, the surfaces that need to be glued

must be carefully cleaned, removing all substances that

may compromise adhesion

(e.g. release agents, preservatives, grease, oils, powders,

old adhesive residue, etc.);

the sealant must be evenly distributed along the entire

perimeter of the frame;

after gluing, leave to dry for approximately 24 hours.

Fig. 1a /1b

CAUTION! Failure to install screws and fasteners in

accordance with these instructions may result in electrical

hazards.

Note: to ensure the correct installation of the product, it is

recommended to tape the pipes using an adhesive with the

following characteristics:

- soft elastic PVC film, with an acrylic-based adhesive

- which complies with DIN EN 60454 regulations

- flame retardant

- excellent resistance against wear

- resistant against temperature fluctuations

- can be used in low temperatures

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG IDK84451IB Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info