820946
26
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
12.8 The ProSense
Technology load detection
The programme duration in
the display is referred to a
medium/high load.
After touching the Start/Pauze - Départ/
Pause button, the maximum declared
load indicator goes off, the indicator
flashes, the ProSense Technology starts
the laundry load detection:
1. The appliance detects the load in the
first 30 seconds, the indicator
flashes, the drum rotates shortly.
2. At the end of the load detection, the
indicator stop flashing. The
programme duration will be adjusted
accordingly and could increase or
decrease. After further 30 seconds,
the water filling starts.
At the end of the load detection, in case
of drum overload, the indicator is
flashing in the display.
In this case, for 30 seconds, it is possible
to pause the appliance and remove the
exceeding garments.
Once removed the exceeding garments,
touch the Start/Pauze - Départ/Pause
button to start the programme again. The
ProSense Technology phase can be
repeated up to three times (see point 1).
Important! If the laundry amount will not
be reduced, the washing programme
starts anyway, despite the overload. In
this case, it will be not possible to
guarantee the best washing results.
About 20 minutes after the
programme start, the
programme duration could
be adjusted again depending
on the capacity of water
absorption of the fabrics.
The ProSense Technology
detection is carried out with
complete washing
programmes only (no
skipping phase selected).
The ProSense Technology is
not available with some
programmes, such as Wol -
Laine, programmes with
short cycles and without
washing phase.
12.9 Programme phase
indicators
When the programme starts the indicator
of the running phase flashes and the
other phase indicators are steady on.
E.g. the washing or pre wash phase is
running: .
When the phase ends the relevant
indicator stops flashing and is steady on.
The next phase indicator starts flashing.
E.g. the rinse phase is running: .
If you select the Plus Steam the steam
phase indicators come on.
The steam phase is running: .
The anti-crease phase is running:
.
12.10 Interrupting a
programme and changing the
options
When the programme is running, you
can change only some options:
1. Touch the button Start/Pauze -
Départ/Pause.
The related indicator flashes.
2. Change the options. The given
information in the display changes
accordingly.
3. Touch the button Start/Pauze -
Départ/Pause again.
The washing programme continues.
12.11 Cancelling a running
programme
1. Press the button Aan/Uit - Marche/
Arrêt to cancel the programme and to
deactivate the appliance.
www.aeg.com26
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für AEG LR73R840 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von AEG LR73R840

AEG LR73R840 Bedienungsanleitung - Deutsch - 48 seiten

AEG LR73R840 Bedienungsanleitung - Holländisch - 48 seiten

AEG LR73R840 Bedienungsanleitung - Französisch - 48 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info