Bedienungsanleitung AEG NKE 103 (Seite 9 von 24) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

648434

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

6. Trouble-Shooting

- The device does not heat: Make sure that the installation circuit breakers are switched on, or that the load shedder (if you

have one) has not switched off the unit power supply. Check the air temperature in the room. For the device equipped,

check that the programmer is in Comfort mode.

- The unit is permanently heating: Make sure that it is not in a draft and that the temperature setting has not been

changed.

- The unit does not carry out programming orders (Device equipped): Make sure that the programming unit is being

correctly used (refer to its user’s manual) or that the Chronocarte is properly inserted in its housing and that it is operating

normally (batteries). The device with electronic control is equipped with a microprocessor that can be distribued by some

severe mains voltage disturbances (outside EC standards defining the disturbance protection level). If there are any

problems (thermostat blocked, etc.) switch off the unit power supply (fuse, circuit breaker, etc.) for about 5 minutes to allow

the unit to start again.

If this phenomenon occurs frequently, control the power supply by your energy supplier.

- The device is very hot on the surface: It is normal that the device when working, the maximum surface temperature is

limited in accordance with standards. However, if you believe that your radiator is still too hot, make sure the power is

adapted to the surface of your room (we recommend 100W / m2) and the unit is not placed in a stream of air that would

disrupt its regulation.



7. Warranty conditions

KEEP THIS DOCUMENT IN A SAFE PLACE

(This certificate should only be produced if you are making a complaint, attached with the invoice of the purchase)

- This guarantee is applicable for 2 years from the date of original purchase

and shall be valid for no more than 30 months from the date of

manufacture.

- The warranty covers the replacement and supply of accepted defective

parts except damages and interest components.

- Labour costs, travel and transportation are under the responsibility of the

user.

- Damage linked to an improper installation, to a supply network not

complying with standards, to an abnormal using or to the non-compliance

to the instructions of the manual are not covered by the warranty.

- Present this certificate only in case of claim with your distributor or installer

attaching your invoice.

- The provisions of these warranty conditions are not exclusives of benefits

for the purchaser of the legal guarantee for defects and hidden defects that

apply in any case in terms of articles 1641 and following of the Civil Code.

* This information is shown on

the plate which can be seen on

the left-side or behind the front

grille of the unit

A Standards, quality labels

B Commercial name

C Commercial reference

D Manufacturing reference

E Serial Number

F Manufacturer number

Type of Device *

Serial Number *

Name and address of the

customer *

DEALER STAMP

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG NKE 103 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info