Bedienungsanleitung AEG NKE 153 (Seite 8 von 24) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

648435

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

areas such as bathrooms and kitchens the power socket must be installed at least 25 cm above the floor. The installation

should be fitted with a double pole break device with a break of at least 3 mm.

- Connection to earth is prohibited / Do not connect the pilot wire (black) to earth. If a master appliance or a slave

appliance is protected by a 30mA differential (e.g. for bathroom) it is necessary to protect the power supply of the pilot wire

on that differential, too.

Commands

Received

No signal

Complete

altermation

230 V

Negative

Half/altermation

– 115V

Positive

Half/altermation

+ 115V

Oscilloscope

Ref/Neutral

Mode

obtained

CONFORT ECO ANTI - FREEZE

STOP HEATING

LOAD SHEDDING

2.3.3 Wall mounted installation (Figure ❼)

- Place the device inclined on the brackets C and rotates the device to place it on the brackets D. Lowering the device on the

bracket. A click indicates that the device is attached and locked. To unlock the attachment tab, grab a screwdriver and

push the tab (at the top left of the attachment tab behind the device) towards the wall. Lift the device while holding the tab

with the screwdriver. Tilt it forward and remove it from the supports C.

3. Utilisation

3.1 How to fix the comfort mode? (Figure ❽)

- The Comfort mode allows setting the desired temperature using the

control knob.

- Put the switch H on , and then set the control knob I on the desired

position, the heating indicator G lights if the ambient temperature is

lower than desired one. Wait until the temperature stabilizes.

3.1.1 How to fix the Eco mode?

- ECO mode allows lowering the temperature of Comfort mode from 3 to

4°C during unoccupied periods of the room. It is recommended that this mode should be used if the room is unoccupied for

more than 2 hours. Put the switch H on ECO and then set the control knob I to the desired position, the heating indicator G

lights if the ambient temperature is lower than desired ECO temperature. Wait until the temperature stabilizes.

3.1.2 How to fix the Frost Free mode?

- It is the position of the switch that keeps the temperature at approximately 7 ° C in the room during prolonged absence from

the house (usually more than 24 hours). Put the switch H on .

3.1.3 How to program your device in Comfort, ECO or Frost Free mode?

- Devices equipped with an electronic thermostat are able to receive orders. There are two solutions:

- By pilot wire (black wire) for devices without plug thanks to the system Chronopass or a wall pilot wire box

- By carrier current with an interface on each device in addition to a Chronopass system or a wall carrier current box.

3.1.4 How to lock the commands (Figure ❾)?

It is possible to lock or limit the use of the control knob I and to lock the switch H to prevent manipulation. Lift the unit from

the wall bracket. On the back of the thermostat, remove the pins J from their support:

- The K position allows locking the control knob.

- The L position allows limiting the utilisation of the control knob.

- The M position allows locking the H switch on the desired mode.

4. Recommendations for use

- There is no point in setting maximum heating; the room temperature will not rise any quicker. If you leave for several hours,

remember to reduce the temperature.

- If you have several units in a room, let them operate simultaneously. This will give you a more uniform temperature without

increasing electricity consumption. This also applies for an unoccupied room; it is more interesting to let the device operate

on a lower setting than turn it off completely.

5. Maintenance

- To maintain performances of your unit, you should clean the upper and lower grids of the unit about twice a year using a

vacuum cleaner or a brush.

- Have a professional check the inside of the unit every five years. Dirt may collect on the grids of the unit if the atmosphere

is polluted. This phenomenon is due to the poor quality of the ambient air. In this case, it is recommended to check that the

room is well ventilated (ventilation, air inlet, etc.), and that the air is clean. The unit will not be replaced under the guarantee

because of this type of dirt. The unit casing should be cleaned with a damp cloth, never use abrasive products.

Indicator for heating. It indicates the

periods in which the resistance is working.

With a stabilized temperature, it flashes

and if the temperature is too high, it stops.

Slider or switch

Control knob of the temperature

Neutral = Blue

Phase = Brown

Pilot Wire = Black

Panel heater cable

Phase

Neutral

Electricity

grid

case: One heater

case: Multiple

heater

Unpiloted device

Pilot wire not connected

To devices with reception box

or central programming

2 possible cases:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG NKE 153 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info