Bedienungsanleitung AEG Oxygen - K (Seite 12 von 16) (Deutsch, Englisch)

551733

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

IN USE

When in use, the power indicator turns green. The 4 progressive

performance bars will appear. A normally functioning unit should have

all 4 performance bars lit. If there are consistently less than 2 bars,

you should check for the problem. Possible issues causing the

performance bars to lessen could be:

1. Blocked suction at the hose end

2. Clogged pipe in system

3. Air restrictive tool being used, such as a crevice tool

4. Full dirt receptacle

5. Clogged ﬁ ltration system

EMPTY DIRT RECEPTACLE

Every 25 hours of use (approximately 6 months) the empty dirt

receptacle indicator will ﬂ ash on the screen. This is an indication to

check the dirt receptacle and empty it. Since this is time based,

you may ﬁ nd the dirt receptacle too empty or too full. If you have

pets, a workshop or other factors that cause waste more frequently,

you may wish to check the dirt receptacle more frequently.

Once the dirt receptacle is emptied, you push the return button

to reset the 25 hours timer. If your power supply is interrupted,

or otherwise unplugged, the empty dirt receptacle indicator will

keep a memory of its previous status and continue life measure.

To manually reset the Empty Dirt Receptacle indicator, simply press

the button lining up with the Enter symbol and hold for 10 seconds.

LIFE METER

The life meter has 8 bars on it. Once these bars are depleted you

unit will continue to run, although it is strongly recommended to

take it to your local authorized dealer/distributor to be inspected and

serviced. A life bar will deplete every 65 hours of vacuum use, meaning

your central vacuum will have a long life of service to you. The life

meter can be reset only by your service technician. If your power

supply is interrupted, or otherwise unplugged, the life meter will

keep a memory of its previous status and continue life measure.

SERVICE INDICATOR

If there is a system fault, or malfunction with your power unit, the

service indicator will ﬂ ash. Upon seeing this symbol, we recommend

that you turn the power unit off, unplug the power supply for

10 seconds and then plug it back in. If the service symbol is still on

the screen, we recommend that you call for service.

This symbol may appear due to the following faults:

• Motor problem

• Electronic problem

• Voltage or current problem (too high or too low)

• Power unit not responding to electronics

SCROLLING YOUR LCD

When not in use, you can scroll through the features of your LCD

to observe the dirt receptacle status, life monitor measure or most

recent recorded power level.

To scroll through these features simply push the button corresponding

with the right pointing arrow symbol.

The next screen you will see will be the Life Meter. Scroll right further

and you will ﬁ nd Bucket Status. Yet another scroll will show you last

recorded performance levels of the power unit, using the Performance

Meter on the In-Use screen. The ﬁ nal scroll right will show you the

customer service phone number.

The button lining up with the left scroll button will allow you to scroll

backwards through the screens.

BAG ADAPTOR

Your power unit can all be ﬁ tted with a convenient paper bag

for more convenient dirt disposal. For maintenance of the paper bag,

please see the Paper Bag Filter section, under Filter Maintenance.

Refer to page 14 - Image 10

UTILITY VALVE

The utility valve is similar to an Inlet valve, but is located near the

power unit. This valve is present for your convenience, as it can

help clean up any dirt spilled close to the central vacuum.

OVERHEATING PROTECTION

If the circuit board reaches an elevated temperature, the power unit the

power unit will not operate and the LED will be off or on LCD model the

screen will be ﬂ ashing. In the event of these problems, press the On/Off

button, unplug hose or wait for temperature to lower. If problems persist;

contact your authorized dealer or distributor.

Refer to page 14 - Image 9

OVERLOAD PROTECTION

The central vacuum system employs features that monitor the following

operating levels: AC voltage, and current draw. If the voltage is below

or above standard operating voltage, high current draw or locked rotor,

the power unit will not operate. In this case the On/Off button will blink

until the problem ceases or on the LCD model the screen will ﬂ ash.

If problems persist; contact your authorized dealer or distributor.

The power unit requires 30 minutes to cool down.

Refer to page 14 - Image 9

DIAGNOSTICS AND MAINTENANCE

Reduced airﬂ ow or suction indicates the central vacuum system

is not operating at maximum efﬁ ciency. If the dirt receptacle is full

and the ﬁ lter is clogged, no air can pass through the unit and no

cleaning can take place. Instructions provided in the booklet serve

as a guide to routine maintenance. Proper airﬂ ow or suction can

be maintained by keeping the dirt receptacle and ﬁ lter clean and

the plastic tubing and hose free from clogs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG Oxygen - K Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AEG Oxygen - K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info