19
PN 2000 R PN 2200 R PN 20 R PN 24 R
.........600 W ................600 W .............. 560 W ............. 620 W
.........300 W ................300 W .............. 280 W ............. 310 W
....0-1290 min
-1
.......0-1290 min
-1
..... 0-1150 min
-1
... 0-1290 min
-1
.......1000 min
-1
..........1000 min
-1
.......... 810 min
-1
...... 1000 min
-1
.......4300 min
-1
..........4300 min
-1
........ 3450 min
-1
...... 4300 min
-1
..........2,7 J ...................2,7 J ................. 1,9 J ............... 2,7 J
...........20 mm ...............22 mm ............. 20 mm ............ 24 mm
...........13 mm ...............13 mm ............. 13 mm ............ 13 mm
...........30 mm ...............30 mm ............. 30 mm ............ 30 mm
...........43 mm ...............43 mm ............. 43 mm ............ 43 mm
..........2,4 kg .................2,4 kg ............... 2,4 kg ............. 2,4 kg
...........10 m/s
2
...............10 m/s
2
............ 10 m/s
2
........... 10 m/s
2
...........94 dB (A) ...........94 dB (A) ......... 94 dB (A) ........ 94 dB (A)
.........105 dB (A) .........105 dB (A) ....... 105 dB (A) ...... 105 dB (A)
ENGLISH
TECHNICAL DATA
Nominal power output .............................................................
Rated output ............................................................................
No-load speed .........................................................................
Speed under load max. ...........................................................
Rate of percussion under load max. ........................................
Single impact strength .............................................................
Drilling capacity in concrete .....................................................
Drilling capacity in steel ...........................................................
Drilling capacity in wood ..........................................................
Chuck neck diameter ...............................................................
Weight without cable ...............................................................
Typical weighted acceleration in the hand-arm area ...............
Typical A-weighted sound levels:
Sound pressure level (K = 3 dB(A)) .......................................
Sound power level (K = 3 dB(A)) ............................................
Measured values determined according to EN 60 745.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the
attached leaflet!
Wear ear protectors.
Exposure to noise can cause hearing
loss.
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Appliances used at many different locations including open
air must be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Sawdust and splinters must not be removed while the
machine is running.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
Do not use diamond core drills on hammer mode.
When working in walls ceiling, or floor, take care to avoid
electric cables and gas or waterpipes.
The dust that arises when working with this tool can be
detrimental to health and therefore not reach the body. Wear
a suitable dust protection mask.
SPECIFIED CONDITIONS OF USE
The rotary pneumatic hammer can be used for hammer
drilling and drilling in wood, metal as well as plastic.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 60745, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3, in accordance with the
regulations 98/37/EC, 89/336/EEC
Volker Siegle
Manager Product Development
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Important note! If the carbon brushes are worn, in addition
to exchanging the brushes the tool should be sent to after-
sales service. This will ensure long service life and top
performance.
Use only AEG accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: AEG Elektrowerkzeuge,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Always disconnect the plug from the socket
before carrying out any work on the
machine.
Accessory - Not included in standard
equipment, available as an accessory.
