Bedienungsanleitung AEG POWERBASE 40 MB (Seite 4 von 24) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

463169

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

5 ENGLISH

TECHNICAL DATA

Voltage range ........................ 9,6-18 V.....................24 V

Quick charge current ...................2,3 A....................1,6 A

Maintaining charge .....................100 mA................100 mA

Battery charging time

1,4 Ah ............................approx 38 min .....approx 55 min

1,7 Ah ............................approx 50 min .....approx 70 min

2,0 Ah ............................approx 55 min .....approx 80 min

2,2 Ah ............................approx 65 min .....approx 90 min

2,4 Ah ............................approx 70 min ...approx 100 min

Weight ........................................500 g ...................500 g

SAFETY INSTRUCTIONS

Please pay attention to the safety instructions in the attached

leaet!

Do not dispose of used battery packs in the household refuse

or by burning them. AEG Distributors offer to retrieve old

batteries to protect our environment.

Do not store the battery pack together with metal objects

(short circuit risk).

Use only System 3000 chargers for charging System 3000

battery packs. Do not use battery packs from other systems.

The following battery packs can be charged with this charger:

voltage battery rating No. of

(of storage battery) battery

cells

7,2 V B 7.2-range

1,4 Ah 6

9,6 V B 9.6-range

1,4 Ah 8

12 V B 12-range

1,2 Ah 10

14,4 V B 14.4-range

1,4 Ah 12

18 V B 18-range

1,4 Ah 15

24 V B 24-range

1,4 Ah 20

9,6 V M 9.6-range

2,2 Ah 8

12 V M 12-range

2,2 Ah 10

14,4 V M 14.4-range

2,2 Ah 12

Do not try to charge non-chargeable batteries with this

charger.

No metal parts must be allowed to enter the battery section of

the charger (short circuit risk).

Never break open battery packs and chargers and store only

in dry rooms. Keep dry at all times.

Please pay attention to the following symbol on the label of

the charger:

This tool is only suitable for indoor use. Never expose

tool to rain.

The battery clamps of the charger are fed by the mains

supply. Do not touch the tool with conducting objects.

Never charge a damaged battery pack. Replace by a new

one.

Before use check machine, cable, and plug for any damages

or material fatigue. Repairs should only be carried out by

authorised Service Agents.

SPECIFIED CONDITIONS OF USE

The quick charger can charge AEG batteries from 9.6 V to 24

Do not use this product in any other way as stated for normal

use.

MAINS CONNECTION

Connect only to a single-phase AC current supply and only to

the mains voltage specied on the rating plate. Connection to

sockets without earth protection is possible as the appliance

features protective insulation to IEC 335. Radio suppression

complies with the European standard EN 55014.

BATTERIES

New battery packs reach full loading capacity after 4 - 5

chargings and dischargings. Battery packs which have not

been used for some time should be recharged before use.

General note concerning NiMH batteries:

The capacity of the battery is reduced when the temperature

falls below -10°C.

Long-term storage at temperatures higher than +40°C may

have negative effects on the capacity of the battery.

CHARACTERISTICS

After inserting the battery into the reception of the charger the

battery will automatically be charged (control lamp is

illuminated continuously)

When a hot or cold battery pack is inserted into the charger

(ashing lamp), charging will begin automatically once the

battery reaches the correct charging temperature.

Standard charging time is approximately 38 minutes (1.4 Ah

battery). Charging time varies depending on the battery

temperature, charge needed and the type of battery pack

being charged.

As soon as charging is completed, the charger switches over

to ”trickle” charge to maintain the full capacity (lamp is

switched off).

The battery can be stored permanently in the charger without

the danger of being overcharged.

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is in

conformity with the following standards or standardized

documents. EN 60335, EN 55014-1, EN 55014-2,

EN 61000-3-2, EN 61000-3-3, in accordance with the

regulations 98/37/EC, 73/23/EEC, 89/336/EEC

Manager Product Marketing and

Development

MAINTENANCE

If the supply cord of this appliance is damaged, it must only

be replaced by a repair shop appopinted by the manufacturer,

because special purpose tools are required

Use only AEG accessories and spare parts. Should

components need to be replaced which have not been

described, please contact one of our AEG service agents (see

our list of guarantee/service addresses).

If needed, an exploded view of the tool can be ordered.

Please state the ten-digit No. as well as the machine type

printed on the label and order the drawing at your local

service agents or directly at: Atlas Copco Electric Tools

GmbH, Postfach 320, D-71361 Winnenden.

SYMBOLS

The battery clamps of the charger are fed by

mains supply. do not touch the tool with

conducting objects.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG POWERBASE 40 MB Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info