Bedienungsanleitung AEG RTi 103 EP (Seite 13 von 36) (Deutsch, Englisch, Holländisch, Französisch)

464371

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

2. Installation instructions

The room temperature regulator must be fitted by an authorised specialist under consideration

of these operation and installation instructions and the operating and installation instructions

of the storage heater.

All electrical connection and installation work must be performed in accordance with the VDE

regulations 0100, the regulations of the electricity supply company responsible and the pertinent

national and regional regulations.

2.1 Technical Data

2.2 Packing Unit

1 room temperature regulator with

– connecting lead charging and discharge control unit

– 6-pole connector with cable harness

1 ON/OFF switch switch with 2 wires

1 potentiometer with connecting lead

1 temperature selector knob

1 Operating and installation instructions

1 room temperature sensor with 2 screws

1 circuit diagram label

1 control panel label

2.3 Installation

Disconnect the storage heater from the power supply before starting installation work.

When connecting the storage heater to an automatic charging control unit, there may be

voltage at the terminals A1/Z1 – A2/Z2 even when the fuses are removed.

When installing several storage heaters in a row make sure that the room temperature controller is

installed in the outside right unit. This guarantees that the room temperature can be measured

properly.

2.3.1 Order of Installation

• Remove air outlet and inlet grille, front wall and right side wall as described in the storage

heater operation and installation instructions;

• Press the dummy caps (1) for the switch and temperature selector knob out of the control panel

at the top and bottom left from the switching area side using a suitable tool.

• Installation of the ON/OFF switch:

Push the black wire (length L = 550 mm) and brown wire with the flat connectors onto the

switch (2) through the holder (3) and snap the holder onto the metal bracket (4).

Press the On/Off switch (2) with the symbol „I“ into the right of the holder.

• Fix the potentiometer (5) with plugged on 3-wire connecting lead from the switching area side

to the angle plate (4) with a screw 4 x 10 mm. It should be noted here that the rotary axis of the

potentiometer is turned to the left (anti-clockwise) and the flat side of the rotary axis is facing

to the right.

• Lay the 3-wire connecting lead of the potentiometer along the back of the angle plate to the

discharge control unit slot (fix the connecting lead to the control panel and the angle plate with

the cable strap).

• Swing forward the angle plate in the switching area to take up the mains terminals after

loosening (not completely unscrewing) the screw in the rear wall.

• Plug the connecting lead (X25) on the discharge control unit (A2) to the charging control unit

(A1) (page 7).

Model

Rated voltage

Connection rating

Control power

RTi 102 E

1/N/PE ~ 50 Hz 230 V

10 A

–

RTi 103 EP

1/N/PE ~ 50 Hz 230 V

10 A with supplementary heating

100 VA

For the User

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG RTi 103 EP Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info