Bedienungsanleitung AEG SB58XX (Seite 6 von 36) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

697584

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

6www.aeg.com

ENGLISH

Thank you for choosing an AEG product. In order to ensure the best results, always use original AEG accessories and

spare parts. They have been designed especially for your product. This product is designed with the environment in

mind. All plastic parts are marked for recycling purposes.

COMPONENTS

A. Jug

B. Spout

C. Lid with ller hole

D. Measuring cup

E. Blade assembly, detachable

F. Motor housing

G. Speed selector (with PULSE, ICE CRUSH function)

H. Cord storage device (underside of appliance)

I. Non-slip feet

Picture page 2-3

GETTING STARTED

1 Before using the blender for the rst time, wash all parts except for the motor housing. Assembling: Place the

rubber seal on the blade assembly (A) and insert it under the jug. Turn the blade assembly counter-clockwise (B) to

fasten.

Caution! The blades are very sharp!

2 Place the blender on a at surface and lock the jug into position on the motor housing. When the arrow is aligned

with the “Locked” indicator, the jug is locked in position. Put the ingredients in the jug. (Do not exceed the maximum

level as indicated on the jug.)

3 Close the lid (A) and insert the measuring cup in the ller hole and (B) lock into position. (You can use the measur-

ing cup to add ingredients while the blender is running. Close the ller hole immediately after, to avoid splashing.)

Caution! When processing hot liquids, see step 4.

4 Processing hot liquids: allow hot liquids to cool down until lukewarm before lling the jug. Fill the jug only half full

and start processing on low speed. The blender jug can become very warm – take care to protect your hands and to

ventilate steam out through the ller hole. Always replace the lid before use.

5 Start the blender: Make sure the speed selector is set to the “OFF”-position. Plug into mains. Turn the speed selector

to your desired setting.

Note: Turn the speed selector to “PULSE, ICE CRUSH” without releasing it, to accelerate the process of blending.

Release to stop.

6 Ice crushing: Turn the speed selector to “PULSE, ICE CRUSH” for 3-5 seconds several times until you obtain a

satisfactory result.

Note: You can add more ice through the ller hole while the blender is running.

CLEANING AND CARE

7 Quick cleaning: Pour warm water into the jug, add a few drops of detergent. Mix water and detergent by turning the

speed selector to “PULSE, ICE CRUSH” briey. Finally, rinse the jug under running water.

8 Thorough cleaning: Turn the blender o and unplug the power cord. Wipe the motor housing with a damp cloth.

Warning! Never immerse the housing, plug, and cord in water or any other uid.

9 Remove the lid and jug. Turn the blade assembly clockwise and remove it. Rinse the blade assembly in water and

detergent. Caution! Handle carefully, the blades are very sharp! The lid, jug and measuring cup can be washed in

the dishwasher.

Enjoy your new AEG product!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG SB58XX Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info