Bedienungsanleitung AEG TBS TB 50 THERMO BODEN (Seite 21 von 76) (Deutsch, Englisch, Holländisch, Französisch)

648290

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Installation – for qualied contractors

» Apply the tile adhesive and levelling compound if

applicable. Take care not to damage the heating

conductor.

» Make sure that the entire circumference and length

of the heating conductor is enclosed in tile adhesive.

» If necessary, lift the heating mat slightly after ap-

plying the tile adhesive to make sure that there are

no air bubbles beneath the heating mat. These may

lead to higher temperatures.

» Press the heating mat back down into the tile

adhesive.

» Lay the tiles in accordance with the manufacturer's

instructions.

9.6.2 Carpet, PVC, parquet or cork

Before laying oor coverings such as carpet, PVC or cork,

cover a large area of the heating mat with a levelling com-

pound.

The levelling compound provides mechanical protec-

tion for the heating mats. Appropriate materials include

free-owing cement mortar, for example.

» Choose an appropriate levelling compound. Note

that this must be able to withstand constant tempera-

tures of at least 80 °C.

» Seal the conduits so that levelling compound can-

not get into the conduits whilst installing the heating

mats.

» Apply the levelling compound in a 5-10 mm

thick layer. Take care not to damage the heating

conductor.

» Make sure that the entire circumference and length

of the heating conductor is enclosed in levelling

compound.

» If necessary, lift the heating mat slightly after apply-

ing the levelling compound to make sure that there

are no air bubbles beneath the heating mat. These

may lead to higher temperatures.

» Press the heating mat back down into the levelling

compound.

» Allow the levelling compound to cure in accordance

with manufacturer's instructions.

» Fill settlement joints with suitable materials, e.g.

silicone.

» Lay the oor covering in accordance with the manu-

facturer's instructions.

9.7 Test measurement 3

After laying the oor covering, check the total resistance

and insulation resistance of the heating mat to rule out

the possibility of damage to the heating mats.

Note

The warranty is not valid without proof of this meas-

urement.

» Measure the total resistance and insulation resist-

ance of the heating mats.

» Check whether the measured values are in the per-

missible measuring range (see chapter "Specica-

tion / Data table").

» Enter the measured values on the warranty card.

9.8 Power supply

WARNING Electrocution

Carry out all electrical connection and installation

work in accordance with relevant regulations.

Observe the local requirements of the relevant

power supply utility.

WARNING Electrocution

Only use a permanent connection to the power sup-

ply.

» Separate the appliance from the power supply

by an additional isolator that disconnects all

poles with at least 3 mm contact separation.

Use mains isolators, fuses, contactors, etc. for

this purpose.

» Install an RCD with a nominal earth leakage cur-

rent of ≦ 30 mA.

Material losses

The heating conductor must not be connected to

the power supply.

» Only connect the cold lead to the power supply.

Material losses

Observe the type plate. The specied voltage must

match the mains voltage.

Design all materials in accordance with the rated

consumption of the appliance.

Basic wiring diagram

(e.g. for temperature controller FRTD 903)

The basic wiring diagram below is provided for clarica-

tion purposes. The temperature controller wiring diagram

is the only applicable wiring diagram (see operating and

installation instructions for the temperature controller).

1 2 3 4 5 6

N L N L

t°

85_07_21_0002

1 2

1 Heating mat

2 Temperature sensor

In connection with the following installation steps, observe

the operating and installation instructions for the temper-

ature controller:

» Connect the earth conductor to the earth connection

(PE).

» Connect the heating mats to the temperature control-

ler via the cold lead.

» Check whether the earth conductor is connected

correctly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG TBS TB 50 THERMO BODEN Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info