Bedienungsanleitung AEG TBS TC 30 THERMO BODEN (Seite 19 von 52) (Deutsch, Englisch, Holländisch, Französisch)

648292

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Installation – for qualied contractors

8.4 Test measurement 1

Before installation, please check the total resistance and

insulation resistance of the heating mats in their delivered

condition.

Note

The warranty is not valid without proof of this meas-

urement.

» Measure the total resistance and insulation resist-

ance of the heating mat.

» Check whether the measured values are in the per-

missible measuring range (see chapter "Specica-

tion / Data table").

» Enter the measured values on the warranty card.

8.5 Preparing the substrate

» Make sure that the substrate is clean, dry, solid and

free from dirt and grease.

» Make sure that no sharp edges or pointed objects

are protruding from the oor. These could damage

the heating conductor.

» If the substrate is not level, carry out levelling oper-

ations so as to avoid cavities beneath the heating

conductor. Settlement joints in the substrate must not

be bridged using the heating mat.

9. Installation

9.1 Installing a ush box

Please install all power cables in a ush box for connec-

tion to the temperature controller.

Material losses

In bathrooms and wet rooms, the ush box must only

be installed outside safety zone 2.

26_07_29_0009_

1 Distribution cable (NYM 3x1.5 mm

)

2 Flush box

3 Conduit for temperature sensor

4 Temperature sensor

5 Cold lead / conduit for cold lead

» Choose an appropriate position to install the ush

box.

» Install an additional ush box if you would like to con-

nect more heating mats.

» Always install an additional ush box if the cold lead

or temperature sensor lead is too short.

9.2 Installing temperature sensors

The temperature sensor must be installed in a conduit.

The conduit is included as standard in the set.

» Choose an appropriate position for installing the con-

duit. Observe the instructions in chapter "Installation

diagram / Position of the temperature sensor".

» Install the conduit and insert the temperature sensor

into it.

9.3 Installing the cold lead

You can install the cold lead in a conduit or ush with the

oor in a groove in the screed.

9.3.1 Installing in a conduit

Material losses

The cold lead must be installed in a separate con-

duit. The cold lead and the temperature sensor lead

must not be installed in the same conduit.

» Install an additional conduit and install the cold lead

in the conduit.

» Make sure that the female connection for the heating

conductor/cold lead is not subjected to a tensile load

of more than 120 N.

9.3.2 Installation in the oor

Material losses

If installed in the oor, the cold lead must be able to

be inserted in the ush box without an extension.

The cold lead may not cross or touch the heating

conductor.

» Chisel out a groove in the screed by using appropri-

ate tools and install the cold lead in this groove.

» Make sure that the female connection for the heating

conductor/cold lead is not subjected to a tensile load

of more than 120 N.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG TBS TC 30 THERMO BODEN Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info