Bedienungsanleitung AEG VH 227 (Seite 16 von 36) (Deutsch, Englisch, Holländisch)

464389

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Installation – for qualied contractors

INSTALLATION

7. Safety

7.1 Country-specic safety information

Observe these installation instructions during installation.

We guarantee trouble-free function and operational

reliability only if the original accessories and spare parts

intended for the appliance are used.

7.2 Instructions, standards and regulations

WARNING Electrocution

All electrical connection and installation work must

be carried out in accordance with VDE regulations

(DIN VDE 0100) [or local regulations], the rules of

your local power supply utility, and relevant national

and local regulations.

WARNING Electrocution

Never use a permanently installed connecting cable.

The appliance must be able to be separated from

the power supply by an isolator that disconnects all

poles with at least 3 mm contact separation.

WARNING Electrocution

Install the appliance in such a way that control

equipment cannot be touched by a person in the

bath or shower.

Material losses

Only t the appliance to a vertical wall that is tem-

perature-resistant to at least 85 °C.

Maintain minimum clearances to adjacent surfaces.

Never install the appliance directly below a wall

socket.

Material losses

Only remove appliance and accessory packaging at

the installation location; look out for the separate

pack.

When unpacking, ensure that no accessory parts

are left in the packaging.

Material losses

Observe the type plate. The specied voltage must

match the mains voltage.

Note

Observe the Building and Garage Regulations [or

local regulations].

Note

When installing the heating appliance in rooms with

a bath and/or shower, observe the safety zone ac-

cording to VDE 0100, section 701, in accordance with

the details on the appliance type plate.

8. Installation

8.1 Appliance installation

To secure the appliance, proceed as follows:

» Unpack the appliance carefully.

» Drill the xing holes in accordance with the

dimensioned drawing in the chapter “Specication”.

» Insert the rawl plugs. The rawl plugs supplied are

suitable for solid walls. For other wall structures,

suitable rawl plugs

must be provided on site.

» Insert the rst screw into the top hole drilled in the

wall, leaving approx. 3 mm of the screw protruding.

Then hook the appliance into the gap between the

wall and the screw head.

» Using the second screw, secure the additional

wall retainer, located at the lower rear part of the

appliance, to the wall.

The appliance can now no longer be removed from

the wall.

8.2 Power supply

» Select a power cable with an adequate

cross-section.

» Install a socket for permanent power supply at a dis-

tance of at least 10 cm from the side of the appliance.

» The power cable must not touch the appliance. Trim

it so it leads directly to the socket. Then strip the

wires and cut the cores to size.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG VH 227 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AEG VH 227

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info