463260

AEG WS 2200-180 Seite 16

16
Zoom out
Zoom in
Vorherige Seite
1/112
Nächste Seite
15
English
GB
Appliances used at many dierent locations including open air should be
connected via a residual current device (FI, RCD, PRCD) of 30mA or less.
Sawdust and splinters must not be removed while the machine is running.
Only plug-in when machine is switched o.
Never reach into the danger area of the plane when it is running.
Always use the auxiliary handle.
Always use the protecting cap when roughing-down and separating.
Immediately switch o the machine in case of considerable vibrations or
if other malfunctions occur. Check the machine in order to nd out the
cause.
Always use and store the grinding disks according to the manufacturer’s
instructions.
When grinding metal, ying sparks are produced. Take care that no
persons are endangered. Because of the danger of re, no combustible
materials should be located in the vicinity (spark ight zone). Do not use
dust extraction.
Due care should be taken that no sparks or sanding dust ying from the
workpiece come into contact with you.
When separating stone the guide shoe must be used!
The adjusting nut must be tightened before starting to work with the
machine.
The workpiece must be xed if it is not heavy enough to be steady. Never
lead the workpiece to the grinding disk with your hand.
Under extreme conditions (e.g. smooth-grinding metals with the arbour and
vulcanizedbre grinding wheel), signicant contamination can build up on
the inside of the angle grinder. For safety reasons, in such conditions the inside
should be cleaned thoroughly of metal deposits and a motor circuit-breaker
must be connected in series. If the motor circuit-breaker trips the machine
must be sent for repair.
For accessories intended to be tted with threaded hole wheel, ensure
that the thread in the wheel is long enough to accept the spindle length.
Use the safety guard from the accessories range when performing out
cutting work.
SPECIFIED CONDITIONS OF USE
The angle grinder may be used for cutting, grinding, sanding and wire
brushing a wide range of materials, such as metal or stone. If you have
any doubts, please refer to the instructions supplied by the accessory
manufacturer.
Do not use this product in any other way as stated for normal use.
MAINS CONNECTION
Connect only to single-phase AC current and only to the system
voltage indicated on the rating plate. It is also possible to connect to
sockets without an earthing contact as the design conforms to safety
class II.
Inrush currents cause short-time voltage drops. Under unfavourable
power supply conditions, other equipment may be aected. If the system
impedance of the power supply is lower than 0,2 Ohm, disturbances are
unlikely to occur.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Do not let any metal parts enter the airing slots - danger of short circuit!
Use only AEG accessories and spare parts. Should components need to be
replaced which have not been described, please contact one of our AEG
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
Article No. as well as the machine type printed on the label and order
the drawing at your local service agents or directly at: AEG Electric Tools
GmbH, Max-Eyth-Straße10, D-71364Winnenden, Germany
SYMBOLS
Please read the instructions carefully before starting
the machine.
CAUTION! WARNING! DANGER!
Always wear goggles when using the machine.
Always disconnect the plug from the socket before
carrying out any work on the machine.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose of electric tools together with
household waste material! In observance of European
Directive 2002/96/EC on waste electrical and electronic
equipment and its implementation in accordance with
national law, electric tools that have reached the end of
their life must be collected separately and returned to
an environmentally compatible recycling facility.
… 16 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für AEG WS 2200-180 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info