20 21
WS 24-180
WS 24-230 WS 24-230 GVX
............... 2400 W ..................
............... 1560 W ..................
............... 8500
min
-1
min
-1
min
-1
................. 180 mm 230 mm
............... M 14 M 14
.................. 5,0 kg
................... 94 dB(A) dB(A) 93
................. 105 dB(A) dB(A) 104
..................... 6 m/s
2
2
5,2
2
.................. 1,5 m/s
2
2
1,5
2
............... < 2,5 m/s
2
2
< 2,5 m/s
2
.................. 1,5 m/s
2
2
1,5
2
ENGLISH
TECHNICAL DA
Rated input
Output
Max. no-load speed
Grinding disk diameter.................................................................
Thread of work spindle
Weight without cable
Noise/Vibration Information
Measured values determined according to EN 60745.T
the
tool are:
Sound pressure level (K
Sound power level (K ...............................................
Wear ear protection!
T
according to EN 60745:
Surface grinding: vibration emission value a
h
Uncertainty K =
Disk sanding vibration emission value a
h
Uncertainty K =
For other applications, e.g.
Wire Brushing other vibration values could occure.
W
instructions, including those given in the accompanying
brochure. Failure to follow the warnings and instructions may
result in electric shock, re and/or serious injury
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Safety Warnings Common for Grinding, Sanding, W
Brushing or Abrasive Cutting-Off Operations:
a) This power tool is intended to function as a grinder
sander Read all safety
warnings, instructions, illustrations and specications
provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, re and/or
serious injury
b) Operations as polishing are not recommended to be
performed with this power tool. Operations for which the
power tool was not designed may create a hazard and cause
personal injury
c) Do not use accessories which are not specically
designed and recommended by the tool manufacturer Just
because the accessory can be attached to your power tool, it
does not assure safe operation.
d) The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can break
and y apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
f) The arbour size of wheels, anges, backing pads or any
other accessory must properly t the spindle of the power
tool.
mounting hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
g) Do not use a damaged accessory
inspect the accessory such as abrasive wheels for chips
and cracks, backing pad for cracks, tear or excess wear
wire brush for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or install an
un
ac
pl
maD
ac
h)
ap
gl
gl
or
st
ma
ge
in
i)
An
eq
F
y
j)
pe
co
co
po
k) If
lo
ar
l)
co
su
m)
Ac
cl
n) T
wi
of
o)
Sp
p) U
wa
W
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ
exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may signicantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged rotating
wheel, backing pad, brush or any other accessory
snagging causes rapid stalling of the rotating accessory which
in turn causes the uncontrolled power tool to be forced in the
direction opposite of the accessory’s rotation at the point of the
binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing the
wheel to climb out or kick out. The wheel may either jump
toward or away from the operator
the wheel’s movement at the point of pinching.
wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below
a) Maintain a rm grip on the power tool and position your
body and arm to allow you to resist kickback forces.
Always use auxiliary handle, if provided, for maximum
control over kickback or torque reaction during start-up.
The operator can control torque reactions or kickback forces, if
proper precautions are taken.
b) Never place your hand near the rotating accessory
Accessory may kickback over your hand.
c) Do not position your body in the area where power tool
will move if kickback occurs. Kickback will propel the tool in
direction opposite to the wheel’s movement at the point of
snagging.
d) Use special care when working corners, sharp edges
etc. A Corners,
sharp edges or bouncing have a tendency to snag the rotating
accessory and cause loss of control or kickback.
e) Do not attach a saw chain, woodcarving blade or
toothed saw blade. Such blades create frequent kickback and
loss of control.
Safety Warnings Specic for Grinding and
Cutting-Off Operations:
a) Use only wheel types that are recommended for your
power tool and the specic guard designed for the
selected wheel. Wheels for which the power tool was not
designed cannot be adequately guarded and are unsafe.
b) The guard must be securely attached to the power tool
and positioned for maximum safety
wheel is exposed towards the operator The guard helps to
protect operator from broken wheel fragments and accidental
contact with wheel.
c) Wheels must be used only for recommended
applications. For example: do not grind with the side of
cut-off wheel. Abrasive cut-off wheels are intended for
peripheral grinding, side forces applied to these wheels may
cause them to shatter
d) Always use undamaged wheel anges that are of
correct size and shape for your selected wheel. Proper
wheel anges support the wheel thus reducing the possibility
of wheel breakage. Flanges for cut-off wheels may be different
from grinding wheel anges.
e) Do not use worn down wheels from larger power tools.
Wheel intended for larger power tool is not suitable for the
higher speed of a smaller tool and may burst.
Additional Safety Warnings Specic for
Off Operations:
a) Do not “jam” the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive depth of
cut. Overstressing the wheel increases the loading and
susceptibility to twisting or binding of the wheel in the cut and
the possibility of kickback or wheel breakage.
b) Do not position your body in line with and behind the
rotating wheel. When the wheel, at the point of operation, is
moving away from your body
the spinning wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a cut for
any reason, switch off the power tool and hold the power
tool motionless until the wheel comes to a complete stop.
Never attempt to remove the cut-off wheel from the cut
while the wheel is in motion otherwise kickback may
occur Investigate and take corrective action to eliminate the
cause of wheel binding.
d) Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully reenter the
cut. The wheel may bind, walk up or kickback if the power tool
is restarted in the workpiece.
e) Support panels or any oversized workpiece to minimize
the risk of wheel pinching and kickback. Large workpieces
tend to sag under their own weight. Supports must be placed
under the workpiece near the line of cut and near the edge of
the workpiece on both sides of the wheel.
f) Use extra caution when making a “pocket cut” into
existing walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects that can
cause kickback.
Safety Warnings Specic for Sanding Operations:
a) Do not use excessively oversized sanding disc paper
Follow manufacturers recommendations, when selecting
sanding paper Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and may cause
snagging, tearing of the disc or kickback.
Safety Warnings Specic for W
a) Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the
wires by applying excessive load to the brush. The wire
bristles can easily penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or brush
with the guard. Wire wheel or brush may expand in diameter
due to work load and centrifugal forces.
Appliances used at many different locations including open air
must be connected via a residual current device.
Dust and splinters must not be removed while the machine is
running.
Only plug-in when machine is switched off.
Never reach into the danger area of the tool when it is running.
Always use the auxiliary handle.
Immediately switch off the machine in case of considerable
vibrations or if other malfunctions occur
order to nd out the cause.
Always use and store the grinding disks according to the
manufacturer's instructions.
When grinding metal, ying sparks are produced. T
that no persons are endangered. Because of the danger of re,
no combustible materials should be located in the vicinity
(spark ight zone). Do not use dust extraction.
Due care should be taken that no sparks or sanding dust ying
from the workpiece come into contact with you.
When separating stone the guide shoe must be used!
The adjusting nut must be tightened before starting to work
with the machine.
The workpiece must be xed if it is not heavy enough to be
steady
hand.
Under extreme conditions (e.g. smooth-grinding metals with
the arbour and vulcanized bre grinding wheel), signicant
contamination can build up on the inside of the angle grinder
For safety reasons, in such conditions the inside should be
cleaned thoroughly of metal deposits and a motor circuit-
breaker must be connected in series. If the motor circuit-
breaker trips the machine must be sent for repair
For accessories intended to be tted with threaded hole wheel,
ensure that the thread in the wheel is long enough to accept
the spindle length.
For cutting or separating use a closed protection cap, available
as an accessory
ENGLISH
