Bedienungsanleitung AEG WSE700 (Seite 2 von 57) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Finnisch)

28731

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

ENGLISH # WS 700-100, WS 700-115, WS 700-125, WSE 700-115

Introduction

You demand the best and buy quality - quality provided by Atlas Copco. We have

built for you a reliable and lasting tool. Working effectively and without endangering

your health is only possible if this instruction for use is read carefully before first us-

ing the tool. We want to satisfy our customers and would like you to buy again AEG

Electric Power Tools from Atlas Copco.

Technical Data

Safety advice ■ Please note safety instructions on red sheet 4 000 333 024!

■ Do not pierce the motor housing as this could damage the double insulation (use

adhesives).

■ Always pull the plug from the mains before making any settings or carrying out main-

tenance.

■ Only plug-in when machine is switched off.

■ Keep mains lead clear from working range of the machine. Always lead the cable

away behind you.

■ Before use check machine, cable, and plug for any damages or material fatigue. Re-

pairs should only be carried out by authorised service agents.

■ After switching off, the machine will not be idle immediately. (After-running of the

work spindle.) Allow the machine to come to a stop before putting down.

■ Never reach into the danger area of the machine when it is running.

■ Always wear safety goggles and ear protectors when working with this machine. It

is further recommended to wear safety gloves, apron, as well as sturdy non-slipping

shoes.

■ Always use the additional handle.

■ Always use the protecting cap when roughing-down and separating.

■ Only use tools whose permitted speed is at least as high as the highest no-load

speed of the machine.

■ Pay attention to the dimensions of the grinding disc. The mounting hole diameter

must fit the mounting flange without play. Do not use reducer pieces or adapters.

■ Check grinding tools before use. The grinding tool must be properly mounted and

turn freely. Perform a test run for at least 30 seconds without load. Do not use dam-

aged, out of round or vibrating grinding tools.

■ Immediately switch off the machine in case of considerable vibrations or if other mal-

functions occur. Check the machine in order to find out the cause.

■ Always use and store the grinding disks according to the manufacturer’s instruc-

tions.

■ When grinding metal, flying sparks are produced. Take care that no persons are en-

dangered. Because of the danger of fire, no combustible materials should be locat-

ed in the vicinity (spark flight zone). Do not use dust extraction.

■ Due care should be taken that no sparks or sanding dust flying from the workpiece

come into contact with you.

Type WS 700-100 WS 700-115 WS 700-125 WSE 700-115

Nominal power (W) 710 710 710 710

Min. no-load speed (min

-1

)2700

Max. no-load speed (min

-1

) 11000 10000 10000 10000

Grinding disk diameter (mm) 100 115 125 115

Thread of work spindle M10 M14 M14 M14

Weight (kg) 1.6 1.6 1.6 1.6

Speed control

–––

•

No-load speed limiter

–––

•

Smooth start

–––

•

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG WSE700 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info