464367
25
Zoom out
Zoom in
Vorherige Seite
1/66
Nächste Seite
27
English
2.2 Technical Description (page 3, fig. 1)
1 Control panel
2 Cover
3 Right side wall
4 Front wall
5 Air outlet grille
6 Air inlet grille
7 Inside front wall
8 Storage blocks
9 Cover plate
10 Thermal insulation
11 Floor thermal insulation
12 Mixing air flap
13 Air duct
14 Cable duct
15 Heating element
17 Safety temperature regulator - charging (N4)
18 Safety temperature limiter (F1)
19 Wall holder
A1 Electronic charging control unit (page 12)
V4 Operating and fault indicator
X16 Control signal adapter 4-stage
X17 4-stage charging factor reducer
2.2.1 Function Principle
The storage blocks are heated up by the heating elements between the rows of storage blocks.
Charging is set continuously with the charging control unit (selector knob fig. 16)
Start and duration of the charging time are determined by the responsible electricity supply
company.
A built-in safety temperature controller (17) and a safety temperature limiter (18) prevent
overheating of the unit. Whilst the safety temperature regulators switch on again automatically,
the safety temperature limiter must be switched back on by the technician by pressing in the knob
in the middle of the limiter after eliminating the cause of the error.
The heat stored in this way is then re-discharged through surface of the unit by natural
convection, radiation and heat conduction.
2.2.2 Electronic Charging Control Unit
Behaviour in case of fault
The charging control unit in the heater is set at the factory to ”positive fault behaviour (80 % PS),
i.e. in the case of a defective charging control unit (e.g. failure of the control signal), the unit is
fully charged.
The unit can be switched to ”negative fault behaviour” (no charging of the storage heater) by
moving the plug-in bridge X16 to position ”80 % NS” when the device is connected to a digital
charging control unit.
Operation with the charging control unit
The appropriate notes in the operating and installation instructions of the charging control unit
must be observed.
Control signal
The electronic charging control unit can be connected to different control signals (ED) of control
units and can therefore be integrated in existing systems.
It is factory set to an AC control signal (AC voltage signal at terminals A1/A2) with 80 % ED.
Other ED signals (68/72, 37/40 %) can be selected by moving the plug-in bridge X16. This is
necessary when the unit is integrated in an already existing system which controls the charging
with one of the named ED signals.
For the Fitter
03 GB WSP_1510S.p65 27.01.2004, 16:3227
25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für AEG WSP 1510 S wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info