Bedienungsanleitung AEG WSP 1510 S (Seite 29 von 66) (Deutsch, Englisch, Holländisch, Französisch)

464367

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

English

Connection

Relieve the strain on the electrical connecting leads as required and connect according to the

electrical circuit diagram in the device (on the inside of the right side wall) or the connection

diagram opposite.

If the angle plate in the switching area for holding the mains terminals is poorly accessible due to

too small a spacing, it can be swung forward during connection work after loosening the screw

(not removing) in the rear wall.

Voltage (230 V) must be applied to the terminal ”L” of the terminal strip X2 during the charging

time.

If no separate power supply is available for this, the terminal ”L1” can be bridged with ”L”. In this

case the terminal ”N” of the terminal strip X2 must always be bridged terminal ”N” of terminal

strip X1.

Please make sure that the protective earth is connected properly!

The cable for connecting a DC control signal must be insulated with a hose inside the unit from the

strain relief to the connecting terminal before connecting.

Control without heater contactor

If no heater contactor is to be installed (partly energy supply company requirement) the thermal

relay installed in the storage heater at the factory can be used.

For this, either the energy supply company signals ”LF” and ”N” or the signals ”SH” and ”N” of the

respective charging control must be connected directly to the terminals ”L-SH” and ”N” of the

storage heater. The notes marked * in the connection diagram must be observed.

L-

Brücken (L) - (L-SH) und (N) - (N)

bei Ansteuerung Heizungsschütz

entfernen

ohne

NNN NN

For the Fitter

The heating elements in the unit are not switched on until the energy supply company has released

the LF and the electronic charging control unit starts charging.

A bridged must be inserted between ”N” and ”A2/Z2” for operation with ”single-wire control”** !

Observe the unit rating plate!

2.5.3 Unit Ready for Operation

Cleaning the unit (fig. 13)

The open unit must be cleaned after installation and insertion of the storage blocks.

Close the unit (fig. 14 and 15)

• Place the inside front panel including heat insulation with the side edging on the supports at the

bottom, press the unit on top and screw together.

• Hang in the right side wall at the bottom, tilt up, hang in at top and fix with screw; (reverse

order see 2.5.1 – disassembly right side wall fig. 6)

• Hang in front wall at top, swing to the heater at the bottom and fix with 2 screws (always use

the two inside threaded holes) (fig. 14);

• Screw on the air outlet grille, screwing the screws hand tight and then back about 1 turn

(fig. 15);

• Place the air inlet grille at an angle on the lugs in the heater base, swing round at the top and

snap in behind the air outlet grille (fig. 15).

Remove the bridges (L) - (L-SH) and

(N) - (N) for control without

contactor

03 GB WSP_1510S.p65 27.01.2004, 16:3231

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG WSP 1510 S Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info