Bedienungsanleitung AEG WSP 3010 (Seite 27 von 62) (Deutsch, Englisch, Holländisch, Französisch)

464353

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

English

For the Fitter

A bridged must be inserted between ”N” and ”A2/Z2” for operation with ”single-wire control”**!

Power adaptation according to rated charging time

By moving or removing bridges at the terminals, the output can be adapted to the rated charging

time specified by the electricity supply company.

Unit rating plate

Observe the labelling on the rating plate and the circuit diagram!

After connecting electrically, the box corresponding to the connection rating and rated charging

time of the unit on the rating plate and the circuit diagram in these installation instructions

should be marked with a smear-proof ballpoint pen.

2.5.3 Unit Ready for Operation

Cleaning the unit (fig. 13 and 14)

The open unit must be cleaned after installation and insertion of the storage blocks.

The fans and the air guidance assembly must be removed for this.

• Unscrew and remove the air guidance assembly (16)

• Lift and remove the fan (18) after loosening (not removing) the screws at the front of the

support brackets (pay attention to cable laying!).

In some units, the discharge temperature control unit (19) including support plate must be

unscrewed.

Make sure the wires are not damaged when setting down the removed parts.

• Clean the floor plate and fan (avoid damage to lamellas!). Then re-install the fans, possibly the

temperature limiter and the air guidance module (correct cable laying!).

Close the unit (fig. 15 and 16)

• Hang in the inside front wall with thermal insulation swung forward slightly at an angle at the

top edge and screw at the bottom edge with 2 screws;

• Hang in the right side wall at the bottom, tilt up, hang in at top and fix with screw; (reverse

order see 2.5.1 – disassembly right side wall fig. 6)

• Hang in front wall at top, swing to the heater at the bottom and fix with 2 screws (always use

the two inside threaded holes) (fig. 15);

• Screw on the air outlet grille, screwing the screws hand tight and then back about 1 turn

(fig. 16);

• Place the air inlet grille at an angle on the lugs in the heater base, swing round at the top and

snap in behind the air outlet grille (fig. 16).

Heating element model

Rated charging time

Connection variants (kW)

Model

WSP 2010

WSP 3010

WSP 4010

WSP 5010

WSP 6010

WSP 7010

➀

2.0

3.0

4.0

5.0

6.0

7.0

8h (series)

➁

1.83

2.75

3.66

4.58

5.5

6.42

10h

➂

1.67

2.5

3.33

4.16

5.0

5.83

6h (heating element fitting set)

➁

2.47

3.76

5.04

5.96

7.42

8.24

➀

2.7

4.1

5.5

6.5

8.1

9.0

➂

2.25

3.42

4.58

5.42

6.75

7.5

3/N/PE ~ 50 Hz 400 V

L2L3123

91,6 % P

Nenn

L2L3N

3/N/PE ~ 50 Hz 400 V

L2L3123

100 % P

Nenn

(Serienverdrahtung)

L2L3

3/N/PE ~ 50 Hz 400 V

L2L3123

83,3 % P

Nenn

L2L3N

8 h 9 h 10 h

100 % P

rated

(series wiring)

91.6 % P

rated

83.3 % P

rated

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG WSP 3010 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info