Bedienungsanleitung AEG WSP 3610 F (Seite 26 von 70) (Deutsch, Englisch, Holländisch, Französisch)

464364

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

2.2 Technical Description (page 3, fig. 1)

1 Control panel

2 Cover

3 Right side wall

4 Front wall

5 Air outlet grille

6 Air inlet grille

7 Fluff screen

8 Inside front wall

9 Storage blocks

10 Cover plate

11 Thermal insulation

12 Floor thermal insulation

13 Mixing air flap

14 Air duct

15 Cable duct

16 Air guidance assembly

17 Heating element

18 Fan

19 Safety temperature regulator for discharge (N5)

20 Safety temperature regulator for charging (N4)

21 Safety temperature limiter (F1)

26 Wall holder

A1 Electronic charging control unit (page 12)

V4 Operating and fault indicator

X16 Control signal adapter 4-stage

X17 4-stage charging factor reducer

2.2.1. Function

The storage blocks are heated up by the heating elements between the rows of storage blocks.

Charging is set continuously with the charging control unit (selector knob fig. 17)

Start and duration of the charging time are determined by the responsible electricity supply

company.

Two built-in safety temperature regulators (19, 20) and a safety temperature limiter (21) prevent

overheating of the unit. Whilst the safety temperature regulators switch on again automatically,

the safety temperature limiter must be switched back on by the technician by pressing in the knob

in the middle of the limiter after eliminating the cause of the error.

The heat stored in this way is then discharged with the aid of a fan, also partly through the heater

surface. In this case, the room air is sucked in through the air inlet grille (6) by the fan (18) and

blown through the air ducts of the storage blocks (9) which heats them up.

Before being output through the air outlet grille (5) the hot air generated in this way is mixed via

two mixing air flaps with colder room air so that the emitted air does not exceed the maximum

permissible temperature. The position of the mixing air flap and thus the

mixing ratio of the air is controlled by a bi-metal controller.

2.2.2 Reducing the Output

By moving or removing bridges at the terminals, the output which is wired to 100% at the factory

can be reduced in connection with a charging factor reduction on the charging control unit by

3 levels (see page 12).

The dimensioning of the line cross sections and the fusing should correspond to the maximum

possible output of the unit.

A single-phase connection may be made according to the ”Technical connection conditions” of

the electricity supply company only up to 2 kW (WSP 1810).

Reducing the charging factor

The electronic charging control unit (A1) contains the plug-in bridge X17 with which the charging

factor of the storage unit can be selected in 4 stages (positions I, II, III or IV) in connection with the

variable connecting lead. Four-stage charging factor adaptation (100 / 90 / 80 70 %). A charging

factor of 100 % (Position I) is pre-selected at the factory.

If the plug-in bridge is plugged to another pin array, this gives a reduced charging factor (switch-

off temperature of the electronic charging control unit is reduced).

For the Fitter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG WSP 3610 F Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info