Bedienungsanleitung AEG X79263MD1 (Seite 5 von 164) (Französisch)

603855

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

ENGLISH

5. CONTROLS

The hood is ﬁ tted with a control panel with

aspiration speed selection control and a

light switch to control cooking area lights.

Use the high suction speed in cases

of concentrated kitchen vapours. It is

recommended that the cooker hood suction

is switched on for 5 minutes prior to cooking

and to leave in operation during cooking

and for another 15 minutes approximately

after terminating cooking.

The control switches are located on the

hood’s front panel:

1A 1B 1C 1D 1E

A. OFF – ON push button

Press once or more to obtain the

function desired:

ON: the hood switches on to the last

speed selected.

OFF: all the functions are switched off

except the illumination.

B. Speed selection push button (extraction

power).

Press this push button once or more

to select the most suitable extraction

speed (power) (1-2-3).

C. The display shows the extraction

power selected, signalling the

saturation of the ﬁ lters F.

D. Intensive speed on/off. The Intensive

speed runs for 5 minutes:

If the hood is on when the Intensive

speed is activated, the hood reverts to

previous speed after 5 minutes.

If the hood is off when the Intensive

speed is activated, the hood will be

turned off after 5 minutes.

To interrupt the Intensive speed, press

button A or B.

E. Light ON/OFF

Should the hood or the controls fail to

operate: disconnect the power supply for at

least 5 seconds, then turn the hood back

on again.

Grease and charcoal ﬁ lter maintenance

indicator

This hood is ﬁ tted with a device that

indicates when maintenace of ﬁ lters should

be done.

If the hood is to be used with a charcoal

ﬁ lter, the saturation

indicator light must be enabled as follows:

Set the hood in “OFF”.

Pressing keys B and D simultaneously for

three seconds, LED F lights up and begins

to ﬂ ash the 1st speed led. After 1 second

the 2nd speed led also ﬂ ashes and the

system emits a sound signal (-Beep-) to

indicate setting taking place.

To remove the charcoal ﬁ lter signal press

push buttons B and D simultaneously for 3

seconds. LED F lights up and begins to

ﬂ ash the 1st speed led (grease ﬁ lter) and

the 2nd speed led. After 1 second, only

the 1st speed led continues to ﬂ ash. The

system emits a sound signal (-Beep-) to

indicate setting taking place.

Grease ﬁ lter LED

The 1st speed led (+ led F) ﬂ ashes, when it

is time to clean the grease ﬁ

lter.

Always comply with the maintenance

instructions for the grease ﬁ lter.

Charcoal ﬁ lter LED

The 2nd speed led (+ led F) ﬂ ashes,

when the charcoal ﬁ lter needs to be

cleaned or replaced.

Resetting the saturation indicator

After cleaning or replacing the ﬁ lters, press

button A for 3 seconds until the 1st speed

led or the second speed led stops ﬂ ashing.

The F LED also turns off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG X79263MD1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info