Bedienungsanleitung Aeris A300 XT (Seite 46 von 56) (Englisch)

618066

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

A300/A300 XT OPERATING MANUAL

CARE AND CLEANING

Protect your unit from shock, excessive temperatures, exposure to chemicals, and tampering. Protect the lens against scratches

with a Instrument Lens Protector. Small scratches will naturally disappear underwater.

• Soak and rinse the unit in fresh water at the end of each day of diving, and check to ensure that the areas around the Low

Pressure (Depth) Sensor (Fig. 124a, 125a), PC Interface Data Port (Fig. 124b, 125b), and buttons are free of debris or

obstructions.

• To dissolve salt crystals, soak in lukewarm water or a slightly acidic bath (50% white vinegar, 50% fresh water). After

removal from the bath, place the unit under gently running fresh water and towel dry before storing.

• Transport your unit cool, dry, and protected.

INSPECTIONS AND SERVICE

Your A300/A300 XT should be inspected annually by an Authorized AERIS Dealer who will perform a factory prescribed func-

tion check and inspection for damage or wear. To keep the 2 year limited warranty in effect, this inspection must be completed

one year after purchase (+/- 30 days).

AERIS recommends that you continue to have an inspection performed every year to ensure it is working properly. The costs of

annual inspections, or inspections relating to water tight integrity, are not covered under the terms of the 2 year limited warranty.

To Obtain Service:

Take your unit to your local Authorized AERIS Dealer.

If required to return your unit to the factory:

• Obtain an RA (Return Authorization) number by contacting AERIS at 510/562-0500 or send an e-mail to service@

oceanicusa.com.

• Record all dive data in the Log and/or download the data stored in memory. All data will be erased during factory service.

• Package it using a protective cushioning material.

• Include a legible note stating the speciﬁc reason for return, your name, address, daytime phone number, serial number(s),

and a copy of your original sales receipt and Warranty Registration.

• Send freight prepaid and insured using a traceable method.

• Non-warranty service must be prepaid. COD is not accepted.

• Additional information is available on the AERIS web site diveaeris.com.

The procedures that follow must be closely adhered to.

Damage due to improper battery replacement is not covered by the product's warranty.

MODULE REMOVAL FROM BOOT (A300 only)

If necessary to remove the A300 module from a console, bend the rubber console boot back to expose the edge of the module.

If the boot is ﬂexible enough to permit, you may bend it back far enough to scoop the module out with your ﬁnger. Otherwise, it

may be necessary to insert a blunt screwdriver until the tip rests just underneath the module.

DO NOT pry the module from the console! Slowly increase the pressure under the module by releasing the tension on the rub-

ber boot. The module will slide up the screwdriver and exit the console.

If the module is in a wrist boot, it will be necessary to peel the lips of the boot downward off the module while applying pressure

from underneath, working it out slowly.

When the battery is removed, settings and calculations for repetitive dives are retained in

the unit's memory while a new battery is installed.

BATTERY REPLACEMENT

The battery compartment should only be opened in a dry and clean environment with extreme care taken to prevent the entrance

of moisture or dust.

To prevent formation of moisture in the battery compartment, it is recommended that the battery be changed in an environment

equivalent to the local outdoor temperature and humidity (e.g., do not change the battery in an air conditioned environment, then

take it outside during a hot sunny day).

Battery Cover Removal

• Turn the unit, or module, over to expose the Battery Cover.

• While applying steady inward pressure on the center of the Battery Cover, rotate the Retaining Ring 10 degrees clockwise

using a cover tool (Fig. 126A) or by pressing against the upper tab of the Ring with a small blade screwdriver (Fig. 126B).

• Lift the Ring up and away from the housing, or turn the unit over to allow the Ring to drop out into your hand.

• Remove the transparent Battery Cover.

Battery Removal

• Remove the Retaining Bar located across the lower portion of the Battery (Fig. 127a).

• Remove the Cover O-ring. DO NOT use tools.

• Slide the Battery up and out of the battery compartment.

Fig. 124 - CASE BACK

(A300 module)





Fig. 126A - RING REMOVAL

(using cover tool)

Fig. 127 - RETAINING BAR



Fig. 125 - CASE BACK

(A300 XT console)





Fig. 126B - RING REMOVAL

(using screwdriver)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aeris A300 XT Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info