Bedienungsanleitung Aeris A300 (Seite 47 von 56) (Englisch)

618065

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

A300/A300 XT OPERATING MANUAL

Inspection

• Closely check all of the sealing surfaces for any signs of damage that might impair proper sealing.

• Inspect the buttons, lens, and housing to ensure they are not cracked or damaged.

WARNING: If damage or corrosion is found, return your unit to an Authorized AERIS Dealer, and DO

NOT attempt to use it until it has received factory prescribed service.

Battery Installation

• Slide a new 3 volt type CR2450 Lithium Battery, ( - ) negative side down into the Battery Compartment. Slide it in from the

right side and ensure that it slides under the contact clip on the left rim (Fig. 128).

• Orient the Retaining Bar across the lower portion of the Battery and carefully push it down into position (Fig. 129).

Battery Cover and Retaining Ring Installation

• Lightly lubricate a new Cover O-ring* with silicone grease and place it on the inner rim of the Battery Cover (Fig. 130).

Ensure that it is evenly seated.

*The O-ring must be a genuine AERIS part that can be purchased from an Authorized AERIS Dealer. Use of any other

O-ring will void the warranty.

• Slide the Cover Ring, top portion ﬁrst (small opening), onto your thumb.

• Carefully place the Battery Cover (with O-ring) into position on the rim of the Battery Compartment, then press it evenly and

completely down into place with your same thumb.

• Maintain the Battery Cover securely in place and, using your other hand, slide the Cover Ring down off your thumb and into

position around the battery compartment.

• The tabs on the Cover Ring ﬁt down into the two slots located at the 2 and 8 o'clock positions.

• Using your ﬁngers, turn the Ring counter clockwise 5 degrees until the tabs engage (Fig. 131), then tighten it 5 more

degrees by turning it counter clockwise with the aide of the cover tool (Fig. 132A) or a small blade screwdriver (Fig. 132B).

• While tightening the Retaining Ring, exert continuous inward pressure on it until it is secured in the proper position. A small

symbol located on the Ring should be aligned with the Locked symbol located on the Housing (Fig. 133a)

Inspection

• Activate the unit and watch carefully as it performs a full diagnostic and battery check, and enters Watch Mode.

• Observe the LCD display to ensure it is consistently clear and sharp in contrast throughout the screen.

WARNING: If there are any portions of the display missing or appearing dim, or if a Low Battery

condition is indicated, return the unit to an Authorized AERIS Dealer for a complete evaluation before

attempting to use it.

RETURNING THE MODULE TO BOOT

• If the boot was ﬁtted with a spacer and it was previously removed, replace the spacer into the boot.

• Orient the module over the opening in the boot, and dip the bottom edge into it while pressing the top edge with the palm

of your hand. Stop pressing when the bottom edge of the module has just entered the boot.

• Correct the alignment of the module as needed so that it is straight.

• Press the module completely into place with your thumbs, watching the alignment, until it snaps into place.

Fig. 128 - INSERTING

BATTERY

Fig. 129 - RETAINING BAR

Fig. 130 - COVER O-RING

Fig. 131 - ENGAGING TABS

Fig. 132A - SECURE COVER

(using cover tool)

Fig. 133 - RING SECURE

Fig. 132B - SECURE COVER

(using screwdriver)



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aeris A300 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info