Bedienungsanleitung Aermec FCW 213V (Seite 36 von 118) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

587614

Zoom out

Zoom in

Vorherige Seite

1/118

Nächste Seite

English

IFCW3LJ 1210 - 5375700_01

LIQUID CRYSTAL DISPLAY

With the remote control on (ON), the display shows the settings of the unit, with the remote control off (OFF) the display is off

and only displays the timer for the programmed activation (if active).

1 - OPERATING MODE

Shows the operating mode:

AUTO automatic

FAN ventilation

COOL cooling

DRY dehumidification

HEAT heating

2 - FAN SPEED

Display of the three fan speeds and the automatic speed control:

AUTO automatic speed control

HIGH high speed

MED medium speed

LOW low speed

3 - HORIZONTAL BLADE POSITION

Displays the four fixed positions of the horizontal blades and oper-

ation with the blades moving.

4 - KEY LOCK

Shows the key lock function is activate.

5 - SLEEP PROGRAMME

Shows the night comfort function SLEEP is active.

6 - TEMPERATURE (°C) OR (°F)

Displays the set point temperature value in °C or °F.

7 - TIMER

Indicates that the timer programmed on or off function has been activated.

8 - TRANSMISSION INDICATOR

Appears every time a button is pushed and it indicates the transmission of the signal.

➀

➁

➂

➃

➄

➅

➆

➇

PREPARATION OF THE REMOTE CONTROL

– Open the battery cover by pressing slightly in the direction of the arrow.

– Insert two 1.5 Volt high-performance alkaline batteries LR 03 (AAA), being careful not invert the polarity.

– Close the battery cover.

IMPORTANT

– The two control types, wired control panel and remote control, cannot be used at the same time on the same fan coil unit.

– The batteries have an average life of 10 months when used normally.

– The two batteries must be identical and must be changed at the same time.

– Remove the batteries from the remote control unit if you envisage the units not being used for long periods.

– When the remote control only works near the fan coil unit, it is time to replace the batteries.

– Do not fix the remote control bracket near a source of heat or in direct sunlight. Avoid exposing the remote control to exces-

sive humidity or knocks (it might break, become deformed, or lose its colour ).

– Do not place the remote control near electronic equipment because it could interfere with the unit's proper operation.

USE OF THE REMOTE CONTROL

– Point the remote control transmitter towards the fan coil receiver while the settings

are being programmed.

– To be able to carry out any operation or change of the settings from the remote con-

trol, the unit must be powered.

– When a signal is received correctly by the FCW it will emit a beep. If you do not

hear the sound, press the remote control button again.

– Obstacles must not be placed between the transmitter and the receiver (e.g. furniture

or curtains) to ensure proper operation.

– The remote control is able to transmit effectively up to 7 metres from the fan coil unit

receiver.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aermec FCW 213V Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info