Bedienungsanleitung Ag neovo MD-24 (Seite 12 von 39) (Englisch)

672376

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

PRECAUTIONS

Notice for the LCD Display

The intended use of the MD-24, MD-27 is to serve as a LCD monitor for integration with the hospital

system.It is designed for general purpose for adults using at hospital environment,continuous operation. For

displaying and viewing of images for reference. The use of this device does not require any direct contact

with patients.

Accessory equipment connected to the analog and digital interfaces must be in compliance with the

respective nationally harmonized IEC standards (i.e. IEC 60950 for data processing equipment, IEC 60065

for video equipment, IEC 61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment.)

Furthermore all congurations shall comply with the system standard IEC 60601-1-1. Everybody who

connects additional equipment to the signal input part or signal output part congures a medical system,

and is therefore, responsible that the system complies with the requirements of the system standard IEC

60601-1-1. The unit is for exclusive interconnection with IEC 60601-1 certied equipment in the patient

environment and IEC 60XXX certied equipment outside of the patient environment. If in doubt, consult the

technical services department or your local representative.

Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle

marked “Hospital Only” or “Hospital Grade”.

Use a power cord that matches the voltage of the power outlet, which has been approved and complies

with the safety standard of your particular country.

The single device output analog signals through ADC element (Analog DigitalConvert) conversion to

become a digital signal and the video signal is via Video Decorder conversion. It has become the same

digital signal, these signals via Scaler IC as zoom in or out action and digital image processing, then

through the cable line transmission LVDS signals to one of the LCD module. The last by the clock controller

(Timing Controller, TCON), the clock signal is transmitted to the drive IC on the panel and turn on Backlight

for LCD module light source by Scaler control.

WARNING: No protection against the ingress of water : IPX0

WARNING: Do not modify this equipment without authorization of the manufacturer. Installation and OSD

adjusting should only be carried by manufacturer trained and authorized personnel.

WARNING: To avoid risk of electric shock, this equipment must only be connected to a supply mains with

with protective earth.

CAUTION: This adapter Manufacturer/model is a forming part of the medical device.

♦ Power by class I power supply.

♦ Adapter manufacturer/model:

ADAPTER TECH: ATM065-P120/ATM065T-P120

Input/output: 100-240V~50-60Hz, 12V( ) 5A.

EDAC TECH:EM10681G

Input/output: 100-240V~50-60Hz, 12V( ) 4.16A.

WARNING: Use suitable mounting apparatus to avoid risk of injury.

WARNING: The equipment not suitable for use in the presence of a ammable anesthetic mixture with air

or with oxygen or nitrous: Not AP or APG Category

CAUTION: No applied part.

Make sure the user not to contact medical device and the patient at the same time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ag neovo MD-24 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ag neovo MD-24

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info